PEX-CM100-T PCI Express Programmable CAN Board, 1-Port CAN 2.0A/2.0B

PISO-CM100U-T is a single-channel CAN interface card for Universal PCI slots. It combines an NXP SJA1000T CAN controller with a Philips 82C250 transceiver and an 80186 microcontroller running at 80 MHz, so message handling runs on the card rather than on the host PC.The onboard processor can filter, preprocess and store CAN messages with timestamps, and transmit them in real time. This reduces the processing load on the host and eases real-time demands on PC applications, even on a busy bus. Data is exchanged with the host through dual port RAM and memory mapping, and a library is supplied for writing custom CAN applications.The card supports CAN 2.0A and CAN 2.0B, with baud rates from 10 k to 1 M bps and a jumper-selectable 120 Ω terminal resistor. Board numbering is set by DIP switch, and the card is plug and play. Drivers cover Windows XP, 7, 8 and 10, with SDK support for VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0 and C# 2008.ApplicationsControl and monitoring of CAN-networked intelligent devices, sensors and actuatorsMonitoring and control systems that integrate diverse communication devices

PISO-CM200U-T CR is a two-channel CAN interface card for universal PCI slots. It suits engineers who need a PC-hosted CAN node that handles message traffic independently of the host, using prioritised CAN messages in distributed control and sensor/actuator networks.The card uses a Bosch C_CAN controller with NXP 82C250 transceivers and supports both CAN 2.0A and CAN 2.0B. An onboard 32-bit microprocessor performs message filtering, pre-processing and timestamped storage, and can also handle real-time transmission. A dual-port RAM mechanism passes data between the host application and the card firmware.Custom CAN applications can be developed with the PISO-CM200U library, with C#.Net, VB.Net and VC++.Net SDK options and a driver for Windows XP, 7, 8.1 and 10 in 32-bit and 64-bit editions. The card is isolated, has a jumper-selectable 120 Ω terminator and a DIP-switch board number.Two CAN ports for 10 k to 1 M bps operationApplicationsMonitoring and control of sensors and actuators on CAN networksCustom CAN Bus applications developed on a Windows PC using the PISO-CM200U libraryIndustrial control and monitoring systems that need a PC-hosted CAN interface

The PEX-CM100-D is a single-channel CAN interface card for PCI Express slots, fitted with a 9-pin D-sub connector. It suits engineers who need a dedicated CAN port with onboard processing, so that real-time frame handling does not fall on the host PC. Its NXP SJA1000T controller supports both CAN 2.0A and CAN 2.0B, with user-defined baud rates from 10 k to 1 M bps.The card ships with built-in default firmware for CAN port communication, and users can load their own firmware for custom message handling. A PC-side monitoring tool assists with debugging user firmware, and the data exchange with the host application takes place through dual-port RAM. Five cyclic transmission sets, timestamping with at least ±1 ms precision and an onboard real-time clock support time-sensitive logging and scheduling.Hardware features include a jumper-selectable 120 Ω terminal resistor, a DIP switch for setting the board number, and isolation rated at 3000 VDC for DC-to-DC and 2500 Vrms for the photocoupler. The card has a PCI Express bus interface and an operating temperature range of 0 ~ +60 °C.ApplicationsNetworking intelligent devices, sensors and actuators within a system or sub-systemCAN applications on PCs that need preprocessing of CAN data streamsCAN systems with high bus loads where no messages should be lost

PEX-CAN200i-D is an active CAN board for PCI Express systems, giving a PC two independent isolated CAN bus channels on a 9-pin D-sub connector. It suits engineers who need a cost-effective way to add CAN connectivity to a host computer for control and monitoring work.The card uses an NXP SJA1000T CAN controller running from a 16 MHz clock, with a 82C250 transceiver. The controller handles bus arbitration, error detection with automatic correction and retransmission. CAN memory is directly mapped, and a jumper selects an on-board 120 Ω terminal resistor.Drivers are provided for Windows and Linux, with support for LabVIEW, DASYLab and InduSoft. Demonstration code is available for VB, VC++, Delphi and BC++, and the SDK covers VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C#.Net and VB.Net.ApplicationsControl and monitoring of CAN bus networksIntegrating diverse communication devices in industrial control systems