PEX-CM100-D PCI Express Programmable CAN Board, 1-Port, 9-Pin D-sub
Single-port programmable CAN board for PCI Express slots, with an onboard 16-bit microcontroller that filters, preprocesses and timestamps CAN traffic to offload the host PC.
- Single CAN port with NXP SJA1000T controller on a 16 MHz clock
- Supports CAN 2.0A and CAN 2.0B with user-defined baud rates from 10 k ~ 1 M bps
- Built-in default firmware, with the option to run user-defined firmware
- Five sets of cyclic transmission and timestamping with at least ±1 ms precision
- Onboard 120 Ω terminal resistor jumper and DIP switch for board number selection
- Dual-port RAM communication with 3000 VDC DC-to-DC and 2500 Vrms photocoupler isolation
€455.00 per piece
| 1-9 pcs | €455.00 | |
|---|---|---|
| 10-30 pcs | €432.00 | −5 % |
| 31+ pcs | €409.00 | −10 % |
Product information "PEX-CM100-D PCI Express Programmable CAN Board, 1-Port, 9-Pin D-sub"
The PEX-CM100-D is a single-channel CAN interface card for PCI Express slots, fitted with a 9-pin D-sub connector. It suits engineers who need a dedicated CAN port with onboard processing, so that real-time frame handling does not fall on the host PC. Its NXP SJA1000T controller supports both CAN 2.0A and CAN 2.0B, with user-defined baud rates from 10 k to 1 M bps.
The card ships with built-in default firmware for CAN port communication, and users can load their own firmware for custom message handling. A PC-side monitoring tool assists with debugging user firmware, and the data exchange with the host application takes place through dual-port RAM. Five cyclic transmission sets, timestamping with at least ±1 ms precision and an onboard real-time clock support time-sensitive logging and scheduling.
Hardware features include a jumper-selectable 120 Ω terminal resistor, a DIP switch for setting the board number, and isolation rated at 3000 VDC for DC-to-DC and 2500 Vrms for the photocoupler. The card has a PCI Express bus interface and an operating temperature range of 0 ~ +60 °C.
Applications
- Networking intelligent devices, sensors and actuators within a system or sub-system
- CAN applications on PCs that need preprocessing of CAN data streams
- CAN systems with high bus loads where no messages should be lost
| Product type: | PCI Express CAN board |
|---|---|
| Interface: | PCI Express |
| Protocol: | CAN 2.0A/2.0B |
| Ports: | 1 |
| Isolation: | 3000 VDC / 2500 Vrms |
| Operating temperature: | 0 ~ +60 °C |
Specifications
| Software | |
|---|---|
| Driver | Windows XP/7/8/10 (32-bit/64-bit OS), InduSoft |
| SDK | VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C# 2008 |
| CPU Module | |
| CPU | 80186, 80 MHz or compatible |
| EEPROM | 16 KB |
| Flash | 512 KB |
| NVRAM | 31 bytes (battery backup, data valid for up to 10 years) |
| SRAM | 512 KB |
| Real Time Clock | Yes |
| LED Indicators | |
| Status | 1 x CAN status 1 x Operating mode |
| PC Bus | |
| Type | PCI Express bus |
| Board No. | By DIP switch |
| CAN | |
| Controller | NXP SJA1000T with 16 MHz clock |
| Ports | 1 |
| Baud Rate | 10 k ~ 1 M bps |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple |
| Terminal Resistor | Jumper for 120 Ω terminal resistor |
| Power | |
| Consumption | 300 mA @ 5 V |
| Mechanical | |
| Dimensions (mm) | 133 x 22 x 98 (W x L x H) |
| Environment | |
| Operating Temperature | 0 ~ +60 °C |
| Storage Temperature | -20 ~ +70 °C |
| Humidity | 5 ~ 85% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Login
Similar products
PISO-CM100U-D is a single-port programmable CAN interface card for Universal PCI slots, suited to engineers who need CAN 2.0A and 2.0B connectivity in a PC. An on-board 80186 microprocessor running at 80 MHz can filter, preprocess and timestamp CAN messages and transmit them in real time, which reduces the processing load on the host PC.The card combines an NXP SJA1000T CAN controller with an 82C250 transceiver and uses dual-port RAM for communication with the host. A real-time clock is fitted, and the board number is set by DIP switch. Drivers are provided for Windows XP, 7, 8 and 10 (32-bit and 64-bit), with SDKs for VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0 and C# 2008. The product is listed with CE, UKCA, FCC, RoHS and WEEE certifications.Custom CAN applications can be developed with the PISO-CM100U library, with data exchanged between the application and the card firmware through memory mapping. A jumper selects the 120 Ω terminating resistor, and isolation is rated at 3000 VDC for DC-to-DC and 2500 Vrms for the photo-coupler.ApplicationsControl and monitoring systems in various industriesCAN network data acquisition and message logging on a PCOffloading CAN data stream preprocessing from host applications
PISO-CM200U-D CR is a universal PCI card that adds two CAN channels to a Windows PC, with a 9-pin D-sub connector. It suits engineers who need a PC-hosted CAN interface that handles message processing on the card rather than in the host.The on-board 32-bit microprocessor filters and pre-processes CAN messages, stores them with a timestamp and manages real-time transmission. The card uses an NXP 82C250 transceiver and a Bosch C_CAN controller, supports both CAN 2.0A and CAN 2.0B, and provides a transmission and reception buffer for up to 256 CAN messages.Custom CAN Bus applications can be developed with the PISO-CM200U library.Data is exchanged between the application and the CAN firmware through memory mapping.Drivers and SDK support are listed for Windows XP, 7, 8.1 and 10 (32-bit and 64-bit), with C#.Net, VB.Net and VC++.Net.ApplicationsControl and monitoring networks built on CAN BusCustom CAN Bus applications developed with the PISO-CM200U library
PEX-CM100-T is a single-channel CAN interface card for PCI Express slots. Its on-board 16-bit microcontroller handles filtering, preprocessing and timestamped storage of CAN messages, as well as real-time transmission, which reduces the processing load on the host PC. An NXP SJA1000T controller and 82C250/251 transceiver provide bus arbitration, error detection and automatic retransmission.The card runs built-in default firmware for CAN port communication, and users can execute their own firmware instead. A PEX-CM100 library is available for developing custom CAN applications, and data is exchanged between the application and the firmware through memory mapping. PC-side monitoring software assists with debugging user-defined firmware.This RoHS variant uses a 5-pin screw terminal connector. It suits engineers who need a PC-hosted CAN node for intelligent devices, sensors and actuators within a system or sub-system.ApplicationsNetworking intelligent devices, sensors and actuators within a system or sub-systemPreprocessing and timestamped storage of CAN data streams on a PCCustom CAN applications developed with the PEX-CM100 library
PEX-CAN200i-D is an active CAN board for PCI Express systems, giving a PC two independent isolated CAN bus channels on a 9-pin D-sub connector. It suits engineers who need a cost-effective way to add CAN connectivity to a host computer for control and monitoring work.The card uses an NXP SJA1000T CAN controller running from a 16 MHz clock, with a 82C250 transceiver. The controller handles bus arbitration, error detection with automatic correction and retransmission. CAN memory is directly mapped, and a jumper selects an on-board 120 Ω terminal resistor.Drivers are provided for Windows and Linux, with support for LabVIEW, DASYLab and InduSoft. Demonstration code is available for VB, VC++, Delphi and BC++, and the SDK covers VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C#.Net and VB.Net.ApplicationsControl and monitoring of CAN bus networksIntegrating diverse communication devices in industrial control systems