I-9K/I-97K

The I-9012 CR is an 8-channel analog input module with 16-bit resolution, designed for applications that need fast, accurate voltage acquisition. Each channel can sample at up to 200 kS/s in single-channel pacer mode, and the input range can be set to ±5 V or ±10 V.Trigger output and trigger input pins allow several I-9012 modules to be chained so that they sample at the same instant, which suits multi-module acquisition where timing alignment matters. An 8 k byte FIFO buffers the conversion data.The module offers 2500 VDC intra-module isolation and ESD protection rated at ±4 kV contact and ±8 kV air. It is listed as RoHS compliant and operates from -25 to +75 °C.ApplicationsSynchronised multi-module data acquisitionHigh-speed voltage measurement in PAC I/O systems

The I-9014 CR is an analog input module for engineers who need fast, accurate voltage and current acquisition within an I-9K/I-97K series system. Its channels can be configured as 16 single-ended or 8 differential inputs using jumpers, covering ±10 V, ±5 V, ±2.5 V, ±1.25 V and ±20 mA ranges.The module's Magic Scan function lets individual channels be sampled at different input ranges. When scanning a single channel, the sampling rate is maintained at 250 kS/s. Magic Scan can run as a standard scan or as a Virtual Sample and Hold function, which offers a lower-cost alternative to hardware sample-and-hold on many analog input cards.A 4 K-word FIFO buffer stores conversions on board. When the sample count passes a pre-defined FIFO level, an interrupt notifies the host, which suits time-critical logging and vibration work where the host must not miss data. Post-trigger external triggering and internal or external start are supported.ApplicationsHigh speed data acquisition systemsVibration analysis

The I-9014C CR is an analog input module for PAC I/O systems that measures eight differential current channels over a ±20 mA range. Its 16-bit converter samples at up to 250 kS/s, making it suited to engineers who need fast, accurate current capture with galvanic separation between the module and the rest of the system.The Magic Scan function gives flexible control over acquisition. Each input channel can be scanned at its own input range, and single-channel scanning can keep the full 250 kS/s rate. Scanning can be run in a standard mode or with a virtual sample-and-hold function, and acquisition can be started internally or by an external trigger using post-trigger mode.A 4 K-word onboard FIFO buffer stores conversion results and raises an interrupt to the host once the sample count passes a pre-defined level, which reduces the load on the host during high-speed capture. The module carries CE, UKCA, FCC, RoHS and WEEE certifications and is listed as RoHS compliant under the CR ordering code.ApplicationsHigh speed data acquisition systemsVibration analysis

The I-9017 CR is a 14-bit analogue input module for engineers who need fast acquisition of voltage and current signals. It offers 16 single-ended or 8 differential input channels, selected by a jumper setting, so the same module can suit either wiring style.Input ranges cover voltage spans of ±1.25 V, ±2.5 V, ±5 V and ±10 V, plus a current range of -20 mA ~ +20 mA. Input impedance is jumper selectable at 20 K, 200 K or 20 M, and the A/D conversion can be triggered by polling or interrupt, depending on the application.Electrical protection includes 2500 VDC intra-module isolation and ESD immunity rated at ±4 kV contact for each terminal and ±8 kV air discharge. The module is suited to high-speed data acquisition, process monitoring and control, and vibration analysis.ApplicationsHigh-speed data acquisition systemsProcess monitoring and controlVibration analysisDigital pattern generation from a digital I/O port

The I-9017-15 is a high-speed analog input module for PAC-based systems that need fast, multi-channel acquisition of voltage and current signals. It offers 14-bit resolution and can be configured with jumpers for 30 single-ended or 15 differential input channels, so the channel layout can match the signal wiring.Input ranges cover ±1.25 V, ±2.5 V, ±5 V and ±10 V for voltage, and -20 mA to +20 mA for current. Current measurement requires an optional external 125 Ω resistor. Input impedance is selectable between 20 kΩ, 200 kΩ and 20 MΩ, and the module supports polling and interrupt A/D trigger modes.Single channel polling mode: about 90 KS/sSingle channel interrupt mode: 50 KS/s15-channel scan mode: 16 KS/sThe module provides 2500 VDC intra-module isolation and ±4 kV contact ESD protection on each terminal. Its 100 KHz bandwidth and low drift specifications suit measurement tasks where timing and stability matter.ApplicationsHigh-speed data acquisition systemsProcess monitoring and controlVibration analysisDigital pattern generation from a digital I/O port

The I-9017C-15 is a high-speed analogue input module from the I-9K/I-97K series, built for engineers who need to capture current signals across 15 differential channels. Each channel accepts ±20 mA and is digitised by a 14-bit converter with a 100 kHz bandwidth.Sampling performance depends on the acquisition mode. Single-channel polling reaches about 90 KS/s, single-channel interrupt mode runs at 50 KS/s, and a 15-channel scan delivers 16 KS/s. The A/D conversion can be triggered by polling or by interrupt, so the module can be matched to the timing requirements of the host application.Intra-module isolation of 2500 VDCESD protection rated at ±4 kV contact and ±8 kV airOperating range of -25 ~ +75 °CCertified to CE, UKCA, FCC, RoHS and WEEE requirementsApplicationsHigh-speed data acquisitionProcess monitoring and controlVibration analysisDigital pattern generation from digital I/O port

I-9024 CR is a 4-channel analog output module for I-9K/I-97K series systems. Each channel is configured individually, so one module can supply a mix of ±10 V voltage outputs and 0 ~ +20 mA current outputs, with 14-bit resolution.Protection features include short circuit protection on the outputs and open wire detection for current outputs. A 3000 VDC intra-module isolation barrier and a ±4 kV contact ESD rating on each terminal help the module tolerate demanding installations. RF immunity is stated to match the levels defined by IEC 61000-4-3.Key operating data includes a response time of 25 us per channel, an accuracy of ±0.1% of FSR for voltage and ±0.2% of FSR for current, and an operating range of -25 ~ +75 °C. Maximum power consumption is 2 W.ApplicationsAnalog control outputs for industrial automation systemsDriving ±10 V voltage inputs and 0 ~ +20 mA current loops on field devices

The I-9024U provides four single-ended analog outputs for engineers who need voltage or current control signals from a PAC I/O system. Each channel can be configured on its own, so a single module can drive a mix of 0 ~ +10 V, ±10 V and current-loop devices without a separate module for each signal type.Output protection and fail-safe behaviour are built in. Short circuit protection is fitted to the outputs, and both a power-on value and a safe value can be set per channel so outputs settle to a defined state at start-up or when communication is lost. Open wire detection is available for the +4 ~ +20 mA range.The module is rated for 3000 VDC intramodule isolation and ±4 kV contact ESD protection on each terminal. It is powered from a 15 ~ 30 VDC terminal block with reverse polarity protection, and draws 2 W maximum. Its operating range is -25 ~ +75 °C, and the housing measures 31 x 134 x 144 mm (W x L x H).

The I-9028U CR is an eight-channel, source-type analogue output module for the I-9K/I-97K series. Each channel is configured on its own, so one module can provide a mix of 0 ~ 5 V, ±5 V, 0 ~ 10 V, ±10 V, +4 ~ +20 mA and 0 ~ +20 mA signals, with the range chosen per channel rather than for the whole module.It suits installations where outputs must start and stay in a known state. Power-on and safe values can be set for the channels, open wire detection is provided for the +4 ~ +20 mA range, and each output is protected against short circuits. The module offers 3000 VDC intramodule isolation and ±4 kV contact ESD protection on each terminal.The module is powered from the terminal block at 15 ~ 30 VDC, draws 2 W maximum and is rated for operation from -25 ~ +75 °C. Its dimensions are 31 x 134 x 144 mm (W x L x H).ApplicationsAnalogue control outputs in I-9K/I-97K PAC I/O systemsExpansion of analogue output points in existing I-9K/I-97K installations

The I-9037P CR is a 16-channel digital output module for PAC I/O applications in the I-9K/I-97K series. Each channel is a source-type (PNP) output with photo-coupler isolation, so it can switch loads of +5 to +30 VDC at up to 700 mA per channel.Engineers typically select this module where output channels must withstand electrically noisy plant conditions. Short-circuit protection, 60 VDC overvoltage protection, 4 kV contact ESD protection and 3750 VDC intra-module isolation help protect the module and the control side of the system.Power-on and safe output values can be configured, so outputs can be set to a defined state at start-up or in a safe state. Channel status LEDs and a power and communication LED simplify commissioning and fault finding. The module draws 1 W maximum and operates from -25 to +75 °C.ApplicationsSwitching PNP-type field loads in industrial automation and control systemsDigital output expansion in I-9K/I-97K PAC I/O configurationsInstallations exposed to electrical noise and interference

I-9040P CR is a 32-channel digital input module from the I-9K/I-97K series for PAC-based I/O systems. Each channel is photo-coupler isolated and can be wired as either a sink-type or source-type input, so one module suits both common input wiring arrangements. It accepts dry contacts, wet (24 V level) signals and 5 V/TTL signals.Wet inputs switch on between +19 VDC and +30 VDC and switch off below +11 VDC, which fits +24 VDC digital input systems. A low pass filter with settings from 1 ms to 70 ms can be selected by jumper or CPU parameter, helping to suppress short-duration noise on field signals. The filter is disabled by default.Each channel has its own status LED, with a further LED for power and communication. For easier field wiring, an optional daughter board such as the DN-37-381-A can be paired with the module. The module provides 3750 VDC intra-module isolation and ±4 kV contact and ±8 kV air ESD protection.ApplicationsDigital status monitoring in +24 VDC input systemsDigital input expansion for PAC-based I/O (I-9K/I-97K series)

The I-9041P CR is a 32-channel sink-type digital output module from the I-9K/I-97K series, designed to switch field loads from an external supply of +10 VDC to +50 VDC. Each channel is rated at 100 mA, and a status LED for every output shows its on/off state.Each output is protected against overvoltage (60 VDC), overload (1.1 A) and short circuits. Power-on and safe values can be configured for the outputs. Field-to-logic isolation of 3750 Vrms and 4 kV ESD protection are included, although channels are not isolated from each other.For simpler wiring, the module can be paired with optional daughter boards such as the DN-37-381-A for easy field termination, or the DN-8K32R for relay output. The CR ordering code is listed as RoHS compliant, and the module is rated for an operating range of -25 ~ +75 °C.ApplicationsSwitching industrial loads, switches and devices from an external 10 to 50 VDC supplyRemote digital output expansion within I-9K/I-97K series PAC I/O systemsField wiring through optional DN-37-381-A daughter boardRelay output switching via DN-8K32R daughter board

The I-9048 is an 8-channel digital input module from the I-9K/I-97K PAC I/O range. Each channel can be set up as an interrupt input, so the controller can respond to a change of state in real time rather than polling the inputs.Interrupts can be programmed on falling edges, rising edges or both. Each input can be jumpered for isolated or non-isolated TTL operation, and the module accepts both dry and wet contact signals. Channel status and power/communication LEDs assist with commissioning and fault finding. The module is restricted to slots 0 to 3 of the backplane.Key electrical and environmental data include 1500 VDC intra-module isolation, ESD protection of ±4 kV contact and ±8 kV air, power consumption of 1.75 W max., and an operating range of -25 ~ +75 °C. The module is CE, UKCA, FCC, RoHS and WEEE listed according to the source data.ApplicationsReal-time system applications requiring hardware interrupt inputEvent and state-change detection on digital input channels in PAC I/O systems

The I-9053P CR is a 16-channel digital input module from the I-9K/I-97K series for PAC I/O applications. Each channel accepts either a dry contact or a wet (voltage) signal, with the input type selected through wire connections, so one module can handle mixed field wiring without changing the hardware.Every channel is photocoupler isolated, and the module provides 3750 VDC intra-module isolation along with ±4 kV contact and ±8 kV air ESD protection, which supports reliable operation in electrically noisy industrial environments. Dry contact inputs can be run over an effective distance of up to 500 m.Each input is supported by an LED indicator, giving a quick visual check of channel status during commissioning and fault finding. The Sink/Source input type and selectable low pass filter (1 ms to 70 ms, set by jumper or CPU parameter, disabled by default) allow the input response to be tuned to the field signals.ApplicationsDigital input monitoring of dry and wet contact switches in industrial environments

The I-9054P CR is an I/O module that combines eight digital inputs with eight digital outputs. The inputs accept either dry or wet contact signals, and dry contact runs can reach up to 500 m. The outputs are photocoupler-isolated open collector stages configured for sink-type operation.Each output channel can be given a configurable power-on value and safe value, so the outputs can be placed in a defined state at start-up or when communication is interrupted. Sixteen LED indicators display the status of the I/O channels, and a further LED shows power and communication status.For electrically demanding installations, the module provides 3750 VDC intramodule isolation and ±4 kV contact ESD protection on each terminal. Its low power draw of 1 W maximum and its -25 ~ +75 °C operating range suit industrial control cabinets.ApplicationsSwitching and monitoring of digital signals in industrial control cabinetsDigital I/O expansion in PAC-based automation systemsInterfacing contact-based sensors and switches with open collector loads in electrically noisy environments

The I-9057P provides 16 isolated digital output channels in a PAC I/O module format, using sink-type open-collector outputs. It suits engineers who need to switch loads from 10 to 50 VDC at up to 100 mA per channel, with photocoupler isolation on every channel.Each channel can be given its own power-on value and safe value, so outputs can be defined for start-up and fault conditions. Per-channel status LEDs show the state of all 16 outputs at a glance, and a further LED indicates power and communication.Protection features include overload protection rated at 1.1 A, short-circuit protection and 60 VDC overvoltage protection. The module is rated for an operating range of -25 to +75 °C and is listed for energy storage system applications.ApplicationsEnergy Storage System

The I-9064 is an 8-channel power relay output module from the I-9K/I-97K series, designed for switching higher-power loads from a PAC I/O system. Each of its eight Form A outputs is rated at 5A for resistive loads, at either 250 VAC or 30 VDC.Each relay channel has its own LED so engineers can see its state at a glance, and a separate LED shows power and communication status. The power-on value and safe value of the outputs can be configured, so the relays can start in a defined state and fall back to a known state as required by the application.For electrically noisy cabinets, the module provides 3000 VDC intra-module isolation and ±4 kV contact ESD protection on each terminal. It operates from -25 to +75 °C and is supplied with CE, FCC, RoHS and WEEE certification marks.ApplicationsHigh-power switching applicationsIndustrial control in harsh environments

The I-9093 CR is a three-axis encoder module for the I-9K/I-97K series. Each axis has a 32-bit counter that reads encoder signals at up to 6 MHz in CW/CCW and Pulse/Dir modes. Its compare trigger outputs fire at set positions with periodic pulses, and the position comparison and pulse generation run entirely in hardware, so the host system carries no software calculation load during operation.Each axis supports Quadrant, CW/CCW and Pulse/Dir encoder modes, with a programmable digital filter from 1 to 250 μs. Reset and latch signal inputs are selectable, and the input threshold is set by jumper to either +3.5 to +5 VDC or 10 to 24 VDC.The module provides 3000 VDC intra-module isolation and 2500 VDC photo-isolation on the encoder inputs. It draws 2 W maximum and is rated for operation from -25 to +75 °C. Dimensions are 31 x 134 x 144 mm (W x L x H).ApplicationsData acquisitionOptical inspection line-scan systemsImage capturePosition measurement

I-9094 is a 4-axis pulse-type motion control module for the XP-9000 and WP-9000 programmable automation controllers. It suits engineers who need general-purpose motion control with independent axes, interpolated moves and encoder feedback on a PAC platform.Most motion functions run on a dedicated motion ASIC rather than the PAC processor, so the CPU load stays low. While the motors are being driven, motion status and the other I/O channels on the PAC can still be monitored. Several motion modules can be fitted to a single controller.Built-in functions include linear and circular interpolation, continuous interpolation, programmable T/S-curve profiles, automatic homing, position comparison and software limits. A set of synchronous actions allows event-triggered responses to be configured on the module.ApplicationsGeneral-purpose motion control applications

The I-9094F is a four-axis motion control module for the XP-9000 and WP-9000 PAC series. It drives stepping or pulse-type servo motors and adds an FRnet master port to the full function set of the I-9094 series, so remote digital I/O can be added without extra wiring complexity.Most motion tasks, including interpolation, T/S-curve acceleration and deceleration, automatic homing and synchronous actions, are handled by a dedicated motion ASIC. This leaves the PAC processor lightly loaded, so one or more of these modules can run in a single controller while motion status and other PAC I/O remain available for monitoring.Engineers choosing this module for multi-axis positioning on a PAC get pulse output at up to 4 Mpps per axis, encoder feedback, and a two-wire FRnet link that scans 128 DI and 128 DO within 2.88 ms. Programming libraries and the EzGo Utility are supplied to shorten development.ApplicationsGeneral-purpose multi-axis motion control on XP-9000 and WP-9000 PAC systemsPositioning with stepping or pulse-type servo motor drivesMachine applications combining motion control with expanded remote digital I/O

The I-9114i CR adds four isolated RS-232 serial ports to PAC and remote I/O systems, letting engineers connect serial devices such as barcode readers, serial printers, intelligent sensors and instrumentation without running a separate serial network.Each port has an internal 128-byte hardware FIFO and supports baud rates up to 115200 bps, with full-duplex communication. Data formats cover 5 to 8 data bits, 1, 1.5 or 2 stop bits, and None, Even, Odd, Mark or Space parity. Each channel is rated at ±4 kV contact ESD (IEC 61000-4-2), and intra-module isolation is 2500 VDC.The module is part of the I-9K/I-97K series and draws 1.75 W maximum. It measures 31 x 134 x 134 mm (W x L x H) and operates from -25 to +75 °C, with storage from -40 to +85 °C.ApplicationsFactory automationBuilding automationHome automationSerial connection of barcode readers and serial printersConnection of intelligent sensors and instrumentation

The I-9144i CR adds four galvanically isolated RS-422/485 serial ports to a PAC or remote I/O system, letting engineers connect several serial devices without sharing a common ground path. Each port has its own internal 128-byte hardware FIFO and runs at up to 115200 bps, with RS-422 full-duplex operation supported.Each port offers a built-in self-tuner or auto-direction control, which simplifies RS-485 half-duplex wiring. Intra-module isolation is rated at 2500 VDC, and onboard ESD protection devices divert discharge from sensitive circuitry, with ±4 kV contact protection on each channel to IEC 61000-4-2.The module suits devices such as bar code readers, serial printers, intelligent sensors, instrumentation equipment and computers, or almost any device fitted with an RS-422/485 port. Parity, data bit and stop bit settings are configurable per the listed options, and status LEDs show power, communication and transmit/receive activity for each port.ApplicationsFactory automationBuilding automationHome automationBar code reader and serial printer connectionIntelligent sensor and instrumentation interfacing

The I-97015 CR is an 8-channel RTD input module from the I-9K/I-97K PAC I/O series, designed for temperature measurement with resistance temperature detectors. Each channel can be configured individually, so a single module can host different RTD sensor types across its inputs.Three-wire RTD connections are compensated automatically, which keeps readings accurate regardless of lead length. Open wire detection and 16-bit resolution support reliable monitoring, while the 3000 VDC intra-module isolation and ±120 VDC overvoltage protection help protect the input stage.Communication is via one RS-485 port using the DCON protocol at 1200 to 115200 bps. The module is rated for an operating range of -25 ~ +75 °C and carries CE, FCC, RoHS and WEEE marks.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

I-97017Z is an analog input module for engineers who need to measure a mix of voltage and current signals on one RS-485 node. Each of its 10 differential or 20 single-ended channels can be assigned an individual input range, from millivolt-level ranges up to 10 VDC and 20 mA, with 0 ~ +20 mA and +4 ~ +20 mA options. Voltage and current input selection is made by jumper.The module is built for harsh signal environments. Every channel tolerates 240 Vrms overvoltage in differential mode, and each analog input includes 50 mA overcurrent protection at 110 VDC/VAC. Per-channel open wire detection is provided for +4 ~ +20 mA inputs, and 3000 VDC intra-module isolation separates the field side from the rest of the circuit.Sampling can be set to normal mode at 10 Hz total or fast mode at 50 Hz total, so the module can be matched to the response time the process requires. A 16-bit resolution, a module watchdog and a communication watchdog support reliable operation, with the module reporting over DCON on a single RS-485 port.ApplicationsIndustrial automationIndustrial machineryBuilding automationFood and beverage systemsSemiconductor fabricationControl systems