PISO-CM200U-D 2-Port Programmable CAN Universal PCI Card, 9-Pin D-sub

PISO-CM200U-T CR is a two-channel CAN interface card for universal PCI slots. It suits engineers who need a PC-hosted CAN node that handles message traffic independently of the host, using prioritised CAN messages in distributed control and sensor/actuator networks.The card uses a Bosch C_CAN controller with NXP 82C250 transceivers and supports both CAN 2.0A and CAN 2.0B. An onboard 32-bit microprocessor performs message filtering, pre-processing and timestamped storage, and can also handle real-time transmission. A dual-port RAM mechanism passes data between the host application and the card firmware.Custom CAN applications can be developed with the PISO-CM200U library, with C#.Net, VB.Net and VC++.Net SDK options and a driver for Windows XP, 7, 8.1 and 10 in 32-bit and 64-bit editions. The card is isolated, has a jumper-selectable 120 Ω terminator and a DIP-switch board number.Two CAN ports for 10 k to 1 M bps operationApplicationsMonitoring and control of sensors and actuators on CAN networksCustom CAN Bus applications developed on a Windows PC using the PISO-CM200U libraryIndustrial control and monitoring systems that need a PC-hosted CAN interface

PISO-CM100U-D is a single-port programmable CAN interface card for Universal PCI slots, suited to engineers who need CAN 2.0A and 2.0B connectivity in a PC. An on-board 80186 microprocessor running at 80 MHz can filter, preprocess and timestamp CAN messages and transmit them in real time, which reduces the processing load on the host PC.The card combines an NXP SJA1000T CAN controller with an 82C250 transceiver and uses dual-port RAM for communication with the host. A real-time clock is fitted, and the board number is set by DIP switch. Drivers are provided for Windows XP, 7, 8 and 10 (32-bit and 64-bit), with SDKs for VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0 and C# 2008. The product is listed with CE, UKCA, FCC, RoHS and WEEE certifications.Custom CAN applications can be developed with the PISO-CM100U library, with data exchanged between the application and the card firmware through memory mapping. A jumper selects the 120 Ω terminating resistor, and isolation is rated at 3000 VDC for DC-to-DC and 2500 Vrms for the photo-coupler.ApplicationsControl and monitoring systems in various industriesCAN network data acquisition and message logging on a PCOffloading CAN data stream preprocessing from host applications

PISO-CM100U-T is a single-channel CAN interface card for Universal PCI slots. It combines an NXP SJA1000T CAN controller with a Philips 82C250 transceiver and an 80186 microcontroller running at 80 MHz, so message handling runs on the card rather than on the host PC.The onboard processor can filter, preprocess and store CAN messages with timestamps, and transmit them in real time. This reduces the processing load on the host and eases real-time demands on PC applications, even on a busy bus. Data is exchanged with the host through dual port RAM and memory mapping, and a library is supplied for writing custom CAN applications.The card supports CAN 2.0A and CAN 2.0B, with baud rates from 10 k to 1 M bps and a jumper-selectable 120 Ω terminal resistor. Board numbering is set by DIP switch, and the card is plug and play. Drivers cover Windows XP, 7, 8 and 10, with SDK support for VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0 and C# 2008.ApplicationsControl and monitoring of CAN-networked intelligent devices, sensors and actuatorsMonitoring and control systems that integrate diverse communication devices

PISO-CAN200U-D is a two-port CAN bus interface card for PCs that gives engineers two independent CAN 2.0A/2.0B channels, each with optical isolation protection. It suits PC-based monitoring and control systems that need to talk to sensors, actuators and intelligent field devices over CAN.Each port is built around an NXP SJA1000T CAN controller with a 16 MHz clock and 82C250/251 transceivers, which handle bus arbitration, error detection with automatic correction and retransmission. The card offers direct memory mapping to the CAN controllers and a jumper-selectable 120 Ω terminal resistor per port. Baud rates are programmable from 10 kbps to 1 Mbps.The universal PCI form factor supports both 5 V and 3.3 V slots (33 MHz, 32-bit, plug and play). Driver support covers Windows and Linux, and the SDK includes VB, VC++, BCB, Delphi and .NET options, with compatibility listed for LabVIEW, DASYLab and InduSoft.ApplicationsControl and monitoring across a range of industrial applicationsBattery exchange stations for electric motorcycles