PISO-CM100U-D Programmable CAN Universal PCI Card, 1-port, 9-pin D-sub
1-port programmable CAN 2.0A/2.0B card for Universal PCI slots, with an on-board 80186 microprocessor for CAN message filtering, preprocessing and timestamping.
- 80186 microprocessor at 80 MHz for filtering, preprocessing and timestamped storage of CAN messages
- NXP SJA1000T CAN controller with 82C250 transceiver
- Supports CAN 2.0A and CAN 2.0B at 10 k ~ 1 M bps
- Timestamps with at least ±1 ms precision, backed by a real-time clock
- Universal PCI, 32-bit, 33 MHz, 3.3 V and 5 V, plug and play
- Single CAN port on a 9-pin D-sub connector with 120 Ω terminator jumper
€434.00 per piece
| 1-9 pcs | €434.00 | |
|---|---|---|
| 10-30 pcs | €412.00 | −5 % |
| 31+ pcs | €391.00 | −10 % |
Product information "PISO-CM100U-D Programmable CAN Universal PCI Card, 1-port, 9-pin D-sub"
PISO-CM100U-D is a single-port programmable CAN interface card for Universal PCI slots, suited to engineers who need CAN 2.0A and 2.0B connectivity in a PC. An on-board 80186 microprocessor running at 80 MHz can filter, preprocess and timestamp CAN messages and transmit them in real time, which reduces the processing load on the host PC.
The card combines an NXP SJA1000T CAN controller with an 82C250 transceiver and uses dual-port RAM for communication with the host. A real-time clock is fitted, and the board number is set by DIP switch. Drivers are provided for Windows XP, 7, 8 and 10 (32-bit and 64-bit), with SDKs for VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0 and C# 2008. The product is listed with CE, UKCA, FCC, RoHS and WEEE certifications.
Custom CAN applications can be developed with the PISO-CM100U library, with data exchanged between the application and the card firmware through memory mapping. A jumper selects the 120 Ω terminating resistor, and isolation is rated at 3000 VDC for DC-to-DC and 2500 Vrms for the photo-coupler.
Applications
- Control and monitoring systems in various industries
- CAN network data acquisition and message logging on a PC
- Offloading CAN data stream preprocessing from host applications
| Product type: | PCI CAN card |
|---|---|
| Interface: | Universal PCI |
| Protocol: | CAN 2.0A/2.0B |
| Ports: | 1 |
| Isolation: | 3000 VDC (DC-to-DC), 2500 Vrms (photo-coupler) |
| Operating temperature: | 0 ~ +60 °C |
| Mounting: | PCI slot |
Specifications
| Software | |
|---|---|
| Driver | Windows XP/7/8/10 (32-bit/64-bit OS), InduSoft |
| SDK | VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C# 2008 |
| CPU Module | |
| CPU | 80186, 80 MHz or compatible |
| EEPROM | 16 KB |
| Flash | 512 KB |
| NVRAM | 31 bytes (battery backup, data valid for up to 10 years) |
| SRAM | 512 KB |
| Real Time Clock | Yes |
| LED Indicators | |
| Status | 1 x CAN status 1 x Operating mode |
| PC Bus | |
| Type | Universal PCI, 3.3 V and 5 V, 33 MHz, 32-bit, plug and play |
| Board No. | By DIP switch |
| CAN | |
| Controller | NXP SJA1000T with 16 MHz clock |
| Ports | 1 |
| Baud Rate | 10 k ~ 1 M bps |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple |
| Terminal Resistor | Jumper for 120 Ω terminal resistor |
| Power | |
| Consumption | 300 mA @ 5 V |
| Mechanical | |
| Dimensions (mm) | 138 x 22 x 105 (W x L x H) |
| Environment | |
| Operating Temperature | 0 ~ +60 °C |
| Storage Temperature | -20 ~ +70 °C |
| Humidity | 5 ~ 85% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Login
Accessories
![CA-0910-C DB9 Female to 3-wire CAN Port Cable [Pin2, Pin3 and Pin7], 1M](https://icpdas-tech.eu/media/d8/ee/9d/1793280036/CA-0910-C-CA-0910-C_la01.webp?ts=1793280036 "CA-0910-C DB9 Female to 3-wire CAN Port Cable [Pin2, Pin3 and Pin7], 1M")
DB9 Female to 3-wire CAN Port Cable [Pin2, Pin3 and Pin7], 1M.
CD-002 is a split ferrite core for suppressing electromagnetic and radio-frequency interference on round cables. Its hinged plastic case closes around the cable and holds the ferrite securely in place, so it can be fitted without re-terminating the cable.The core is aimed at low-frequency noise generated by engine control units, inverters and motors. It can be retrofitted to installed equipment or added during post-assembly work on the data and power cables of electronic devices, which suits environments where EMI or RFI affects signal integrity.Each package contains 10 cores, supplied in white and rated for an operating temperature of -40 °C to 75 °C. Maximum cable diameter is Ø13 mm.ApplicationsSuppressing low-frequency noise from engine control unitsReducing noise from inverters and motorsReducing EMI and RFI on data cables of electronic equipmentReducing EMI and RFI on power cables of electronic equipmentRetrofitting existing installations
CNT-CAN CR is a CAN bus connector for linking a CAN bus node to the bus line quickly. Its quick-connect technology removes the need to strip the bus conductors, which simplifies installation.The connector has a plastic housing with an integrated terminating resistor that can be selected with a built-in switch. It provides two cable entries and a 9-pin D-Sub female connector with a 90° cable outlet, and is available with a programming interface.It suits engineers who need to add a CAN device to an existing CAN bus line with minimal wiring work and a clear choice of bus termination.ApplicationsConnecting a CAN bus node to a CAN bus lineAdding CAN devices to an existing CAN bus network
5 Pins M12 A Code Assembly Plug (Female).
Similar products
PISO-CM100U-T is a single-channel CAN interface card for Universal PCI slots. It combines an NXP SJA1000T CAN controller with a Philips 82C250 transceiver and an 80186 microcontroller running at 80 MHz, so message handling runs on the card rather than on the host PC.The onboard processor can filter, preprocess and store CAN messages with timestamps, and transmit them in real time. This reduces the processing load on the host and eases real-time demands on PC applications, even on a busy bus. Data is exchanged with the host through dual port RAM and memory mapping, and a library is supplied for writing custom CAN applications.The card supports CAN 2.0A and CAN 2.0B, with baud rates from 10 k to 1 M bps and a jumper-selectable 120 Ω terminal resistor. Board numbering is set by DIP switch, and the card is plug and play. Drivers cover Windows XP, 7, 8 and 10, with SDK support for VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0 and C# 2008.ApplicationsControl and monitoring of CAN-networked intelligent devices, sensors and actuatorsMonitoring and control systems that integrate diverse communication devices
PISO-CM200U-D CR is a universal PCI card that adds two CAN channels to a Windows PC, with a 9-pin D-sub connector. It suits engineers who need a PC-hosted CAN interface that handles message processing on the card rather than in the host.The on-board 32-bit microprocessor filters and pre-processes CAN messages, stores them with a timestamp and manages real-time transmission. The card uses an NXP 82C250 transceiver and a Bosch C_CAN controller, supports both CAN 2.0A and CAN 2.0B, and provides a transmission and reception buffer for up to 256 CAN messages.Custom CAN Bus applications can be developed with the PISO-CM200U library.Data is exchanged between the application and the CAN firmware through memory mapping.Drivers and SDK support are listed for Windows XP, 7, 8.1 and 10 (32-bit and 64-bit), with C#.Net, VB.Net and VC++.Net.ApplicationsControl and monitoring networks built on CAN BusCustom CAN Bus applications developed with the PISO-CM200U library
PISO-CM200U-T CR is a two-channel CAN interface card for universal PCI slots. It suits engineers who need a PC-hosted CAN node that handles message traffic independently of the host, using prioritised CAN messages in distributed control and sensor/actuator networks.The card uses a Bosch C_CAN controller with NXP 82C250 transceivers and supports both CAN 2.0A and CAN 2.0B. An onboard 32-bit microprocessor performs message filtering, pre-processing and timestamped storage, and can also handle real-time transmission. A dual-port RAM mechanism passes data between the host application and the card firmware.Custom CAN applications can be developed with the PISO-CM200U library, with C#.Net, VB.Net and VC++.Net SDK options and a driver for Windows XP, 7, 8.1 and 10 in 32-bit and 64-bit editions. The card is isolated, has a jumper-selectable 120 Ω terminator and a DIP-switch board number.Two CAN ports for 10 k to 1 M bps operationApplicationsMonitoring and control of sensors and actuators on CAN networksCustom CAN Bus applications developed on a Windows PC using the PISO-CM200U libraryIndustrial control and monitoring systems that need a PC-hosted CAN interface
PISO-CAN200U-D is a two-port CAN bus interface card for PCs that gives engineers two independent CAN 2.0A/2.0B channels, each with optical isolation protection. It suits PC-based monitoring and control systems that need to talk to sensors, actuators and intelligent field devices over CAN.Each port is built around an NXP SJA1000T CAN controller with a 16 MHz clock and 82C250/251 transceivers, which handle bus arbitration, error detection with automatic correction and retransmission. The card offers direct memory mapping to the CAN controllers and a jumper-selectable 120 Ω terminal resistor per port. Baud rates are programmable from 10 kbps to 1 Mbps.The universal PCI form factor supports both 5 V and 3.3 V slots (33 MHz, 32-bit, plug and play). Driver support covers Windows and Linux, and the SDK includes VB, VC++, BCB, Delphi and .NET options, with compatibility listed for LabVIEW, DASYLab and InduSoft.ApplicationsControl and monitoring across a range of industrial applicationsBattery exchange stations for electric motorcycles