MN-SERVO-DAA-EC Motionnet Single-axis Motion Control Module, Delta ASDA-A/A2
Single-axis Motionnet slave module with Mini-Clamp connector for Delta ASDA-A/A2 servo drives. It adds axis control to a Motionnet fieldbus over a standard Cat.5 LAN cable.
- Single-axis Motionnet module for Delta ASDA-A/A2 servo drives, connected directly to the driver
- Up to 64 axes per line, with a maximum communication speed of 20 Mbps
- Pulse output rate of 6.6 MHz (Max.) and 28-bit pulse and encoder counters
- Multi-axis linear and 2-axis circular interpolation, with T/S-curve acceleration and deceleration
- Slow-down, home, positive and negative limit sensor inputs for each axis, plus software limits and compare trigger output
- Three-way isolation for power, communication and I/O
290,00 € per piece
| 1–9 pcs | 290,00 € | |
|---|---|---|
| 10–30 pcs | 281,00 € | −3 % |
| 31+ pcs | 275,00 € | −5 % |
Informations sur le produit "MN-SERVO-DAA-EC Motionnet Single-axis Motion Control Module, Delta ASDA-A/A2"
The MN-SERVO-DAA-EC CR is a distributed single-axis motion control module that connects directly to a Delta ASDA-A/A2 servo driver and extends a Motionnet network. Each module is chained to the next with a serial Cat.5 LAN cable, which reduces the wiring between drivers and the controller in integrated machine automation projects.
Motion features include trapezoidal and S-curve acceleration and deceleration, multi-axis linear interpolation, 2-axis circular interpolation, and the ability to change speed and position on the fly. Each axis has slow-down, home, positive and negative limit sensor inputs, plus software limits and compare trigger output. Up to 64 axes can be controlled per line.
This CR variant uses an e-CON Mini-Clamp connector, which makes wire termination easier and leaves less debris than conventional wiring. Power, communication and I/O are three-way isolated for better noise immunity and device protection. The module is rated for 24 VDC ±5% input and an operating range of 0 ~ +60 °C.
Applications
- Distributed single-axis motion control on a Motionnet fieldbus
- Integrated machine automation with Delta ASDA-A/A2 servo drives
| Product type: | Motion control module |
|---|---|
| Interface: | Motionnet |
| Protocol: | Motionnet |
| Isolation: | 1000 V |
| Power input: | 24 VDC ±5% |
| Operating temperature: | 0 ~ +60 °C |
Specifications
| LED Indicators | |
|---|---|
| Status | Communication state (Link, Error) Internal 3.3 V Power Termination Resistor Switch Mechanic Switch Input |
| General | |
| Speed Profile | Trapezoidal/S Shaped Acc/Dec Driving |
| Auto-Home Search | 13 Types |
| Axis I/O | |
| Servo Interface Output | SVON, ERC, ALM_RST |
| Latch Input | Yes (shared with SD) |
| Mechanical Switch Input | LMT+, LMT-, HOME, SD, EMG |
| Position Compare Output | High-Speed 5 V TTL or 24 V open collector |
| Servo Interface Input | ALM, RDY, INP |
| Encoder Input | |
| Mode | CW/CCW, A/B phase |
| Counter Width | 28-bit |
| Pulse Output | |
| Mode | OUT/DIR, CW/CCW |
| Counter Width | 28-bit |
| Rate | 6.6 MHz (Max.) |
| Motionnet | |
| Communication Connectors | Mini-Clamp Connector |
| Transfer Speed | 2.5, 5, 10, 20 Mbps |
| Power | |
| Input Range | 24VDC +/-5% (1000 V isolated) |
| Environment | |
| Operating Temperature | 0 ~ +60 °C |
| Storage Temperature | -20 ~ +80°C |
| Humidity | 10 ~ 90% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Connexion