PISO-CAN400U-FD-D 4-Port Isolated CAN FD Universal PCI Card

The PISO-CAN400U-FD-T is a PC-based CAN bus card that gives a Windows or Linux host four independent, isolated CAN FD ports. It suits engineers who need several CAN or CAN FD networks on one PCI slot, with each port wired through a 5-pin screw terminal connector.The card is built around a Microchip MCP2518FD CAN FD controller and TI TCAN1042HG series transceivers. It supports ISO 11898-2 and CAN 2.0 A/B, and CAN FD can run in either ISO or non-ISO (Bosch) mode, selectable in the configuration. Message filtering, a DIP-switch board number and a jumper-selectable 120 Ω terminal resistor help when integrating the card into an existing bus.This ordering code includes an ADP-9-T board. Drivers are supplied for Windows 7/8.1/10 and Linux 5.10, and demos and libraries are provided for C#.Net, VB.Net and VC++.Net, so application development can start quickly.ApplicationsControl and monitoring of CAN and CAN FD networks from a PCIntegrating diverse communication devices into industrial control and monitoring systems

PISO-CAN400U-D adds four independent CAN bus 2.0A/2.0B ports to a PC through a single universal PCI card. Each port uses an NXP SJA1000T controller and provides optical isolation on the bus side, which helps protect the host PC from faults and ground disturbances on the network.The card suits engineers building CAN networks around a PC-based supervisory or data acquisition system. Its universal PCI design accepts both 5 V and 3.3 V slots, and it is plug and play on a 33 MHz, 32-bit bus. Each port has a jumper-selectable 120 Ω terminal resistor, so termination can be set port by port to match the network layout.Drivers and SDKs are provided for Windows and Linux, with support for LabVIEW, DASYLab and InduSoft, and the SDK covers several common development environments. The vendor states that the card has been verified to drive 100 CAN nodes simultaneously.ApplicationsLogistics management systemsControl and monitoring of industrial CAN networks linked to a PCSensor and actuator networking within machine or sub-system control

PISO-CAN400U-T is a four-port CAN bus interface card for PCs that need several independent CAN networks on one host. Each port supports CAN 2.0A and 2.0B and runs at a programmable rate up to 1 Mbps, so one card can serve multiple buses with different timing requirements.Each CAN port is optically isolated, with 2500 Vrms photo-couple isolation on the bus and 3000 VDC DC-to-DC isolation, which helps protect the host PC from faults on the field side. A jumper selects the 120 Ω terminal resistor independently for each port, and the card has been verified to drive 100 CAN nodes simultaneously.The card is built around an NXP SJA1000T CAN controller with a 16 MHz clock and 82C250/251 transceivers, with direct memory mapping to the controllers. It is a universal PCI card that works in both 3.3 V and 5 V PCI slots, and it is plug and play. Drivers are provided for Windows and Linux, along with support for LabVIEW, DASYLab and InduSoft, plus SDKs for several development environments.ApplicationsLogistics management systemsControl and monitoring across various industries

PISO-CAN200U-D is a two-port CAN bus interface card for PCs that gives engineers two independent CAN 2.0A/2.0B channels, each with optical isolation protection. It suits PC-based monitoring and control systems that need to talk to sensors, actuators and intelligent field devices over CAN.Each port is built around an NXP SJA1000T CAN controller with a 16 MHz clock and 82C250/251 transceivers, which handle bus arbitration, error detection with automatic correction and retransmission. The card offers direct memory mapping to the CAN controllers and a jumper-selectable 120 Ω terminal resistor per port. Baud rates are programmable from 10 kbps to 1 Mbps.The universal PCI form factor supports both 5 V and 3.3 V slots (33 MHz, 32-bit, plug and play). Driver support covers Windows and Linux, and the SDK includes VB, VC++, BCB, Delphi and .NET options, with compatibility listed for LabVIEW, DASYLab and InduSoft.ApplicationsControl and monitoring across a range of industrial applicationsBattery exchange stations for electric motorcycles