PISO-CAN400U-D Universal PCI CAN Card, 4-Port Isolated CAN 2.0A/2.0B
Four-port isolated CAN 2.0A/2.0B interface card for 3.3 V and 5 V PCI slots, with 2500 Vrms photo-coupler isolation and programmable rates up to 1 Mbps.
- Four independent CAN bus 2.0A/2.0B communication ports, each with a 9-pin D-sub connector
- Optical isolation on the CAN bus, rated at 2500 Vrms photo-coupler and 3000 VDC DC-to-DC
- Programmable transfer rate from 10 kbps up to 1 Mbps
- Jumper-selectable 120 Ω terminal resistor for each port
- Universal PCI card for 3.3 V and 5 V slots, 33 MHz 32-bit PCI bus (V2.1), plug and play
- Direct memory mapping to the CAN controllers
€558.00 per piece
| 1-9 pcs | €558.00 | |
|---|---|---|
| 10-30 pcs | €530.00 | −5 % |
| 31+ pcs | €502.00 | −10 % |
Product information "PISO-CAN400U-D Universal PCI CAN Card, 4-Port Isolated CAN 2.0A/2.0B"
PISO-CAN400U-D adds four independent CAN bus 2.0A/2.0B ports to a PC through a single universal PCI card. Each port uses an NXP SJA1000T controller and provides optical isolation on the bus side, which helps protect the host PC from faults and ground disturbances on the network.
The card suits engineers building CAN networks around a PC-based supervisory or data acquisition system. Its universal PCI design accepts both 5 V and 3.3 V slots, and it is plug and play on a 33 MHz, 32-bit bus. Each port has a jumper-selectable 120 Ω terminal resistor, so termination can be set port by port to match the network layout.
Drivers and SDKs are provided for Windows and Linux, with support for LabVIEW, DASYLab and InduSoft, and the SDK covers several common development environments. The vendor states that the card has been verified to drive 100 CAN nodes simultaneously.
Applications
- Logistics management systems
- Control and monitoring of industrial CAN networks linked to a PC
- Sensor and actuator networking within machine or sub-system control
| Product type: | PCI CAN card |
|---|---|
| Interface: | PCI |
| Protocol: | CAN 2.0A/2.0B |
| Ports: | 4 |
| Isolation: | 2500 Vrms (photo-couple) |
| Operating temperature: | 0 ~ +60 °C |
Specifications
| Software | |
|---|---|
| Driver | Windows XP/7/8/10 (32-bit/64-bit OS), Linux 2.6.x ~ 5.4.0, LabView, DASYLab, InduSoft |
| SDK | VB 6.0, VC++ 6.0, BCB 6.0, Delphi 4.0, C#.Net, VB.Net |
| PC Bus | |
| Type | Universal PCI, 3.3 V and 5 V, 33 MHz, 32-bit, plug and play |
| CAN | |
| Controller | NXP SJA1000T with 16 MHz clock |
| Ports | 4 |
| Baud Rate | 10 k ~ 1 M bps |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple |
| Terminal Resistor | Jumper for 120 Ω terminal resistor |
| Power | |
| Consumption | 300 mA @ 5 V |
| Mechanical | |
| Dimensions (mm) | 126 x 85 x 22 (W x L x D) |
| Environment | |
| Operating Temperature | 0 ~ +60 °C |
| Storage Temperature | -20 ~ +70 °C |
| Humidity | 5 ~ 85% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Login
Accessories
![CA-0910-C DB9 Female to 3-wire CAN Port Cable [Pin2, Pin3 and Pin7], 1M](https://icpdas-tech.eu/media/d8/ee/9d/1793280036/CA-0910-C-CA-0910-C_la01.webp?ts=1793280036 "CA-0910-C DB9 Female to 3-wire CAN Port Cable [Pin2, Pin3 and Pin7], 1M")
DB9 Female to 3-wire CAN Port Cable [Pin2, Pin3 and Pin7], 1M.
CD-002 is a split ferrite core for suppressing electromagnetic and radio-frequency interference on round cables. Its hinged plastic case closes around the cable and holds the ferrite securely in place, so it can be fitted without re-terminating the cable.The core is aimed at low-frequency noise generated by engine control units, inverters and motors. It can be retrofitted to installed equipment or added during post-assembly work on the data and power cables of electronic devices, which suits environments where EMI or RFI affects signal integrity.Each package contains 10 cores, supplied in white and rated for an operating temperature of -40 °C to 75 °C. Maximum cable diameter is Ø13 mm.ApplicationsSuppressing low-frequency noise from engine control unitsReducing noise from inverters and motorsReducing EMI and RFI on data cables of electronic equipmentReducing EMI and RFI on power cables of electronic equipmentRetrofitting existing installations
CNT-CAN CR is a CAN bus connector for linking a CAN bus node to the bus line quickly. Its quick-connect technology removes the need to strip the bus conductors, which simplifies installation.The connector has a plastic housing with an integrated terminating resistor that can be selected with a built-in switch. It provides two cable entries and a 9-pin D-Sub female connector with a 90° cable outlet, and is available with a programming interface.It suits engineers who need to add a CAN device to an existing CAN bus line with minimal wiring work and a clear choice of bus termination.ApplicationsConnecting a CAN bus node to a CAN bus lineAdding CAN devices to an existing CAN bus network
5 Pins M12 A Code Assembly Plug (Female).
Similar products
PISO-CAN400U-T is a four-port CAN bus interface card for PCs that need several independent CAN networks on one host. Each port supports CAN 2.0A and 2.0B and runs at a programmable rate up to 1 Mbps, so one card can serve multiple buses with different timing requirements.Each CAN port is optically isolated, with 2500 Vrms photo-couple isolation on the bus and 3000 VDC DC-to-DC isolation, which helps protect the host PC from faults on the field side. A jumper selects the 120 Ω terminal resistor independently for each port, and the card has been verified to drive 100 CAN nodes simultaneously.The card is built around an NXP SJA1000T CAN controller with a 16 MHz clock and 82C250/251 transceivers, with direct memory mapping to the controllers. It is a universal PCI card that works in both 3.3 V and 5 V PCI slots, and it is plug and play. Drivers are provided for Windows and Linux, along with support for LabVIEW, DASYLab and InduSoft, plus SDKs for several development environments.ApplicationsLogistics management systemsControl and monitoring across various industries
PISO-CAN400U-FD-D is a universal PCI card that gives a host PC four independent, isolated CAN bus ports. It supports both classic CAN 2.0 A/B and CAN FD, so one card can serve legacy CAN networks and newer higher-throughput designs with larger data fields.Each port uses a 9-pin D-sub connector, and an ADP-9-D board is supplied with the card. The design is built around a Microchip MCP2518FD CAN FD controller and TI TCAN1042HG series transceivers, with bus arbitration, error detection, automatic correction and retransmission handled in hardware. Bus termination is selected with an onboard jumper for a 120 ohm terminal resistor, and the board number is set by DIP switch.Drivers are provided for Windows 7/8.1/10 and Linux 5.10, together with demos and libraries for C#.Net, VB.Net and VC++.Net. The card suits engineers building control and monitoring systems that need several CAN channels in a single PC.ApplicationsControl and monitoring of CAN-connected devices across various industriesMulti-channel CAN and CAN FD communication from a PC
The PISO-CAN400U-FD-T is a PC-based CAN bus card that gives a Windows or Linux host four independent, isolated CAN FD ports. It suits engineers who need several CAN or CAN FD networks on one PCI slot, with each port wired through a 5-pin screw terminal connector.The card is built around a Microchip MCP2518FD CAN FD controller and TI TCAN1042HG series transceivers. It supports ISO 11898-2 and CAN 2.0 A/B, and CAN FD can run in either ISO or non-ISO (Bosch) mode, selectable in the configuration. Message filtering, a DIP-switch board number and a jumper-selectable 120 Ω terminal resistor help when integrating the card into an existing bus.This ordering code includes an ADP-9-T board. Drivers are supplied for Windows 7/8.1/10 and Linux 5.10, and demos and libraries are provided for C#.Net, VB.Net and VC++.Net, so application development can start quickly.ApplicationsControl and monitoring of CAN and CAN FD networks from a PCIntegrating diverse communication devices into industrial control and monitoring systems
PISO-CAN200U-D is a two-port CAN bus interface card for PCs that gives engineers two independent CAN 2.0A/2.0B channels, each with optical isolation protection. It suits PC-based monitoring and control systems that need to talk to sensors, actuators and intelligent field devices over CAN.Each port is built around an NXP SJA1000T CAN controller with a 16 MHz clock and 82C250/251 transceivers, which handle bus arbitration, error detection with automatic correction and retransmission. The card offers direct memory mapping to the CAN controllers and a jumper-selectable 120 Ω terminal resistor per port. Baud rates are programmable from 10 kbps to 1 Mbps.The universal PCI form factor supports both 5 V and 3.3 V slots (33 MHz, 32-bit, plug and play). Driver support covers Windows and Linux, and the SDK includes VB, VC++, BCB, Delphi and .NET options, with compatibility listed for LabVIEW, DASYLab and InduSoft.ApplicationsControl and monitoring across a range of industrial applicationsBattery exchange stations for electric motorcycles