PISO-CAN200U-FD-T Universal PCI CAN FD Card, 2-Port Isolated CAN Bus Interface

The PISO-CAN200U-FD-D is a PCI card that gives a host PC two independent CAN FD bus ports, each brought out on a 9-pin D-sub connector. It is intended for engineers who need to attach a PC to CAN FD networks while keeping the bus electrically isolated from the computer.The card is built around a Microchip MCP2518FD controller with TI TCAN1042HG series transceivers. It is compatible with ISO 11898-2 and with CAN 2.0 A/B and CAN FD. Message filter configuration is supported, and the board number is set with a DIP switch, which helps when more than one card is installed.Drivers are supplied for Windows 7, 8.1 and 10 and for Linux 5.10, with demos and libraries for C#.Net, VB.Net and VC++.Net. A built-in jumper selects the 120 Ω terminal resistor for the CAN bus.ApplicationsControl and monitoring of CAN FD networks from a PCIntegrating diverse CAN-connected devices into a single host

PISO-CAN200U-D is a two-port CAN bus interface card for PCs that gives engineers two independent CAN 2.0A/2.0B channels, each with optical isolation protection. It suits PC-based monitoring and control systems that need to talk to sensors, actuators and intelligent field devices over CAN.Each port is built around an NXP SJA1000T CAN controller with a 16 MHz clock and 82C250/251 transceivers, which handle bus arbitration, error detection with automatic correction and retransmission. The card offers direct memory mapping to the CAN controllers and a jumper-selectable 120 Ω terminal resistor per port. Baud rates are programmable from 10 kbps to 1 Mbps.The universal PCI form factor supports both 5 V and 3.3 V slots (33 MHz, 32-bit, plug and play). Driver support covers Windows and Linux, and the SDK includes VB, VC++, BCB, Delphi and .NET options, with compatibility listed for LabVIEW, DASYLab and InduSoft.ApplicationsControl and monitoring across a range of industrial applicationsBattery exchange stations for electric motorcycles

PISO-CAN200U-T is a PCI card that adds two independent CAN bus ports to a PC, so engineers can connect controllers, sensors and actuators to a CAN network with real-time, prioritised messaging. Each port uses a 5-pin screw terminal connector.The card is built around an NXP SJA1000T CAN controller running from a 16 MHz clock, and it handles CAN 2.0A and 2.0B frames. Optical isolation on the CAN bus, rated at 2500 Vrms, protects the host PC from faults on the network side. A jumper selects the 120 Ω terminal resistor for each port.As a universal PCI card, it fits both 5 V and 3.3 V PCI slots and works as a plug and play device. Drivers and SDKs are provided for Windows and Linux, along with support for LabVIEW, DASYLab and InduSoft. The sibling model PISO-CAN200U-D is listed as a similar product.ApplicationsControl and monitoring systems in various industriesIntegrating diverse communication devices on a CAN networkBattery exchange stations for electric motorcycles

PISO-CAN400U-D adds four independent CAN bus 2.0A/2.0B ports to a PC through a single universal PCI card. Each port uses an NXP SJA1000T controller and provides optical isolation on the bus side, which helps protect the host PC from faults and ground disturbances on the network.The card suits engineers building CAN networks around a PC-based supervisory or data acquisition system. Its universal PCI design accepts both 5 V and 3.3 V slots, and it is plug and play on a 33 MHz, 32-bit bus. Each port has a jumper-selectable 120 Ω terminal resistor, so termination can be set port by port to match the network layout.Drivers and SDKs are provided for Windows and Linux, with support for LabVIEW, DASYLab and InduSoft, and the SDK covers several common development environments. The vendor states that the card has been verified to drive 100 CAN nodes simultaneously.ApplicationsLogistics management systemsControl and monitoring of industrial CAN networks linked to a PCSensor and actuator networking within machine or sub-system control