DN-37-381 DB37 to Screw Terminal Board, 3.81 mm Pitch, DIN-Rail Mount

Female DB37 to Screw Terminal Board (Pitch= 5.08 mm) with DIN-rail Mounting. Include: CA-3720AM (DB37 Male to Female, with Moding case, 45º, 2M).

The DN-37-381-A breaks out a 37-pin D-sub connection into two 19-pin screw terminal blocks with 3.81 mm pitch, mounted on a DIN rail. It gives engineers a practical way to connect field wiring to DB37-equipped data acquisition hardware without terminating individual wires at the D-sub connector.This ordering code includes a CA-3710A DB37 male-to-female cable, 45º, 1 m, so the board can be connected to a DB37 source straight away. The board measures 99 mm x 82 mm and is intended for DIN-rail installation.The board is rated for an operating temperature of 0 ~ 60°C and a storage temperature of -20 ~ 70°C, with 5% ~ 90% RH non-condensing humidity. It carries CE, UKCA, FCC, RoHS and WEEE markings.ApplicationsWiring field signals to DB37 data acquisition boardsPanel-mounted I/O connection in control cabinets

The DN-37/N-A breaks out a 37-pin D-sub connection into screw terminals, so field wiring can be landed on a terminal board rather than made directly to the DAQ card. It suits engineers who need a practical wiring point for signals coming from a DB37 interface.The board provides two 19-pin screw terminal blocks on a 5.08 mm pitch, with a second 37-pin D-sub connector available for expansion. It is rated for a maximum current of 1 A and a DC voltage of 50 V, with a dielectric withstanding voltage of 250 VAC for one minute.This ordering code includes a 1 m male-to-female DB37 cable. The board is specified for an operating temperature of 0 ~ 60 °C and carries CE, UKCA, FCC, RoHS and WEEE marks.ApplicationsTerminating field wiring for DAQ boards with DB37 connectorsExpanding signal connections from a 37-pin D-sub interface

DN-37/N CR breaks out two 37-pin D-sub connectors onto 19-pin screw terminal blocks at 5.08 mm pitch, giving engineers a practical way to wire field signals to a DAQ daughter board without building a custom harness. The board carries two DB37 female connectors, so one can be used for expansion while the other serves the primary connection.Electrical ratings listed for the DN-37 series are a current rating of 1 A maximum, a DC rating of 50 V maximum and a dielectric withstanding voltage of 250 VAC for one minute. The board measures 144 mm x 72 mm and is rated for an operating temperature of 0 ~ 60°C, with storage from -20 ~ 70°C and 5% ~ 90% RH non-condensing humidity.This code is supplied with a CA-3710 cable (DB37 Male to Male, 45º, 1M) so the board can be connected to a compatible DAQ module straight out of the box. Note that the DIN-rail mounting noted for the DN-37 series is not part of the DN-37/N CR description, so check the mechanical details before specifying it for a rail-mounted cabinet.ApplicationsWiring field signals to DB37-based DAQ daughter boardsInterconnecting data acquisition hardware with screw terminal connections

The DN-37/2 CR is a DIN-rail mounted breakout board that brings a DB37 female D-sub connection out to two 19-pin screw terminal blocks on a 5.08 mm pitch. It suits engineers who need to wire field signals to DB37-equipped data acquisition hardware without working directly at the D-sub pins.The board carries two 37-pin D-sub connectors, one for the connection to the host and one for expansion. This ordering code includes the CA-3720 DB37 male-to-male cable, 45º, 2 m, so the board can be connected to the host device straight out of the box.Electrical ratings are 1 A maximum current, 50 V maximum DC and 250 VAC dielectric withstanding voltage for one minute. The board measures 144 mm x 72 mm and is rated for 0 ~ 60°C operation.ApplicationsField wiring breakout for DB37-equipped data acquisition hardwareTerminating signal wiring on a DIN-rail panel

The DN-37 CR is a female DB37 to screw terminal board for wiring field signals to DB37-based data acquisition hardware. It provides two 37-pin D-sub connectors, one of which is intended for expansion, and two 19-pin screw terminal blocks with a 5.08 mm pitch, mounted on a DIN-rail.This ordering code includes a CA-3710 cable, a DB37 male-to-male, 45º, 1 m assembly, so the board can be connected to a compatible DB37 device straight out of the box. The board is rated for up to 1 A and 50 V DC, with a dielectric withstanding voltage of 250 VAC for one minute.Measuring 144 mm x 72 mm, the board is suited to control cabinets where a DIN-rail footprint is required. It is specified for an operating range of 0 ~ 60°C and carries CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsField wiring for DB37-based data acquisition boardsScrew terminal breakout in DIN-rail control cabinets

The DN-37-A is a DIN-rail mounted terminal board that takes signals from a female DB37 D-sub connector and presents them on screw terminals with a 5.08 mm pitch. It suits engineers who want to wire field signals to a DB37-based I/O board without making individual cable terminations.The board carries two 37-pin D-sub connectors, one of which is provided for expansion, and two 19-pin screw terminal blocks. The DN-37-A CR ordering code includes a CA-3710A DB37 male-to-female cable, 45º, 1 m, so the board can be connected to a compatible DB37 device straight out of the box.Electrical ratings are 1 A maximum current, 50 V maximum DC rating and a dielectric withstanding voltage of 250 VAC for one minute. The board measures 144 mm x 72 mm and is rated for 0 ~ 60°C operation.ApplicationsField wiring termination for DB37-connected I/O signals