PET-7017 PoE I/O Module, 8-ch Analog Input, 4-ch Digital Output

The ET-7017 CR is an Ethernet I/O module that brings eight differential analogue inputs and four digital outputs onto a Modbus network. Each analogue channel can be set to voltage or current and given its own input range, which suits mixed sensor setups without changing hardware. This ordering code is listed with RoHS compliance.The digital outputs are isolated open-collector sink types rated at 700 mA per channel, with short-circuit and overload protection. Power-on and safe values are programmable, so outputs can be defined for start-up and fault conditions. Sampling can be switched between normal mode at 10 Hz and fast mode at 50 Hz across all channels.Host communication uses Modbus TCP or Modbus UDP over a single 10/100 Base-TX RJ-45 port. A built-in web server and web HMI are provided, Ethernet access is controlled by ID, password and IP filter, and dual watchdog functions are included.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The ET-7217 CR is an Ethernet remote I/O module for engineers who need to acquire sensor signals and switch outputs over a Modbus network. It provides eight differential analogue inputs, each of which can be configured with its own range. Input type is set by jumper, so each channel can accept voltage or current, and the inputs are protected against overvoltage up to 240 Vrms.On the network side, the module includes a 2-port 10/100 Base-TX switch with LAN bypass, which allows devices to be daisy-chained along a line. It supports Modbus TCP and Modbus UDP, and includes a built-in web server with web HMI, access control by ID, password and IP filter, and communication security features. The sampling rate can be switched between normal and fast modes.The four digital outputs are isolated open-collector sink types with short-circuit and overload protection, and can be given programmable power-on and safe values. The module offers 2500 VDC I/O isolation and 4 kV ESD protection, and is designed for DIN-rail mounting over an operating range of -25 ~ +75 °C.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

The PET-7217 CR is a PoE-powered Ethernet I/O module with eight differential analogue inputs and four digital outputs, communicating over Modbus TCP or Modbus UDP. Each analogue channel can be given its own input range, and the input type (voltage or current) is selected by jumper for the corresponding channel.A built-in 2-port 10/100 Base-TX switch with LAN bypass allows modules to be daisy-chained along a line. The unit can be powered from PoE (IEEE 802.3af, Class 1) or from a +12 ~ +48 VDC terminal block, and includes a built-in web server, Web HMI and dual watchdogs.The digital outputs are isolated open-collector sink types with short-circuit and overload protection, and both power-on and safe values are programmable. Intra-module isolation is rated at 2500 VDC.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The PET-7017-10 is a PoE-powered Ethernet analog input module for engineers who need voltage or current measurement on a networked I/O node. Its inputs can be set as 10 differential or 20 single-ended channels in software, and each channel can be given its own range, so one module can serve mixed sensor types on the same network.Each channel offers a choice of voltage ranges from ±150 mV to ±10 V and current ranges of ±20 mA, 0 ~ 20 mA and 4 ~ 20 mA, selected with jumpers. Resolution is 16-bit, and the module has two sampling modes: normal mode at 10 Hz total and fast mode at 50 Hz total. Open wire detection is available for 4 ~ 20 mA inputs, and differential channels are rated for 240 Vrms overvoltage protection.Configuration and monitoring are handled through a built-in web server with Web HMI, and the module supports Modbus TCP and Modbus UDP. Access is controlled by ID, password and IP filter. The unit is powered either from PoE (IEEE 802.3af, Class 1) or from a +12 ~ +48 VDC terminal block, and it mounts on a DIN rail.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment