PET-7016 PoE I/O Module, 2-ch Strain Gauge Input, 2-ch DI, 2-ch DO

The ET-7016 is an Ethernet I/O module for remote strain gauge measurement. It provides two differential analogue input channels that accept full-bridge, half-bridge and quarter-bridge wiring, along with a 0 ~ 10 V excitation output to power the bridge. Each analogue input can be configured with its own range, covering millivolt, voltage and current spans, so a single module can handle mixed sensor types.On the digital side, the module offers two wet-contact inputs that can also count pulses, and two isolated open-collector outputs rated at 700 mA per channel. The digital outputs can be set as alarm outputs. Long-distance measurements are supported with compensation for the voltage loss along the cable run.Communication is handled through a single 10/100 Base-TX RJ-45 port using Modbus TCP or Modbus UDP. A built-in web server and web HMI allow configuration and monitoring, and access can be restricted by ID, password and IP filter. Dual watchdogs and I/O pair connection add to the module's operational reliability, and it mounts on a DIN rail.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The PET-7002 CR combines three analog inputs, six digital inputs with counter capability and three Form A power relay outputs in a single Ethernet module that can be powered over PoE or from a +12 ~ +48 VDC terminal block. Each analog input is set by jumper to voltage or current, with ranges from ±150 mV to ±10 V, 0 ~ 20 mA, ±20 mA and 4 ~ 20 mA, and is protected against 240 Vrms overvoltage.Engineers will find the module convenient for remote I/O because it provides Modbus TCP and Modbus UDP, a built-in web server with web HMI, and communication security with access control by ID, password and IP filter. A dual watchdog and I/O pair connection support resilient operation, and the relay outputs have programmable power-on and safe values.The module offers 2500 VDC intra-module isolation and 4 kV ESD protection, and it is rated for an operating range of -25 ~ +75 °C. It is intended for DIN-rail installation and is listed as RoHS compliant.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The PET-7024 CR combines analogue output, digital input and digital output channels in one DIN-rail Ethernet module. Its four analogue outputs can be set by jumper to voltage or current, covering +/-5 V, +/-10 V, 0 ~ 20 mA and 4 ~ 20 mA, so one module can drive a range of field actuators and controllers. The five digital inputs accept dry or wet contacts and include a 32-bit counter, while the five digital outputs are isolated open-collector sink types.Power can be supplied over Ethernet via IEEE 802.3af Class 1 PoE or from a +12 ~ +48 VDC terminal block, which simplifies cabling in cabinets where a separate supply is not convenient. Modbus TCP and Modbus UDP are supported, and the built-in web server and web HMI allow configuration and monitoring from a browser.This RoHS-compliant variant is suited to building automation, factory and machine automation, and remote maintenance and diagnosis. Its 2500 VDC intra-module I/O isolation and 4 kV ESD protection help protect the module in electrically demanding installations.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

PET-7026 CR combines six analog inputs, two analog outputs, two digital inputs and two digital outputs in one DIN-rail Ethernet module. It suits engineers who need mixed signal acquisition and control at a single network node, with Modbus TCP and Modbus UDP available for host communication.Each analog input can be set to voltage or current and to a range from ±500 mV to ±20 mA or 4 ~ 20 mA, selected by jumper. The inputs are rated for 240 Vrms overvoltage protection, and the analog outputs can likewise be configured for voltage or current using their jumpers. The digital inputs support dry or wet contact and can count pulses up to 32-bit.Suitable for deployments where power and data share one Ethernet cable, using PoE (IEEE 802.3af, Class 1) or a +12 ~ +48 VDC terminal block supply.Built-in web server and Web HMI simplify configuration and monitoring.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment