DN-68A 68-pin SCSI-II Female I/O Connector Block, DIN-rail

The DN-68 CR is a DIN-rail mounted terminal board that breaks out the 68-pin SCSI-II connector of the PISO-ENCODER300(U) and PISO-ENCODER600(U) encoder input boards onto pin-to-pin screw terminals. It gives engineers a practical way to land field wiring without working directly on the SCSI-II cable.Each signal is presented on a screw terminal in a one-to-one arrangement with the connector pins, which keeps cabinet wiring straightforward to trace and maintain. The board measures 103 mm x 86 mm and is designed for standard DIN-rail installation in control panels.The DN-68 CR is rated for an operating range of -20 ~ +75 °C and a storage range of -30 ~ +85 °C, with 10 ~ 90% RH non-condensing humidity. It carries CE, UKCA, FCC, RoHS and WEEE markings.ApplicationsField wiring of encoder inputs on PISO-ENCODER300(U) and PISO-ENCODER600(U) boardsMotion control panels requiring DIN-rail mounted terminal connections

The DN-8237DB is a motion control daughter board that adds two axes of stepper or servo drive interfacing to compatible ICP DAS 2-axis motion controllers, such as the I-8092F and PISO-PS200. It is set up for the Delta ASDA-A servo amplifier and suits engineers who need a clean, isolated wiring point between the controller and the drive.Each axis has its own group of signals: pulse command lines, encoder feedback, special-purpose inputs for home, near-home and limit switches, and a servo-enable output. Signals terminate on screw terminals, and the axis connectors can be swapped to change which axis is assigned to which group, so the wiring does not need to be redone.An onboard power module accepts 20 ~ 26 VDC and supplies the voltages needed by the board's own circuitry. Power and status LEDs, including home and limit switch indication, help with commissioning and fault finding.ApplicationsTwo-axis stepper or servo positioning with Delta ASDA-A servo amplifiersPulse-command motion control using ICP DAS 2-axis motion controllersConnecting encoder feedback and limit or home sensors to a motion controller

The DN-8237GB CR is a 2-axis motion control terminal board for ICP DAS controllers such as the I-8092F and PISO-PS200. It breaks out pulse command lines, encoder feedback, home, near-home and limit switch inputs and a servo-enable output for each axis, so stepper or servo drives can be wired directly to the controller.Each axis has its own group of signals, and the terminal connectors can be swapped to change axis assignment without rewiring. Onboard photo-coupling isolation helps protect the controller, and an integrated power module generates the voltages needed by the board from a 20 ~ 26 VDC supply.Suited to general purpose drives, Mitsubishi and Panasonic motor amplifiers.FRnet terminal available for high-speed serial I/O expansion where the controller supports FRnet.Applications2-axis stepper motor motion control2-axis servo motor motion controlConnecting ICP DAS motion controllers to general purpose, Mitsubishi and Panasonic motor amplifiers

The DN-8237MB CR is a motion control daughter board that pairs ICP DAS 2-axis motion controllers with Mitsubishi MELSERVO-J2 servo amplifiers. It is designed to be fitted to compatible controllers such as the I-8092F and PISO-PS200, and it supports pulse command type stepper or servo motors.Signals are routed through screw terminals grouped by axis. Each group carries the pulse output command lines, encoder feedback lines, special purpose inputs (home, near home and limit switches) and a servo-enable output. Connectors can be swapped to reassign axis definitions without rewiring, and onboard photo-coupling isolation helps protect the controller.An onboard power module generates the voltages needed by the board from a wide 20 ~ 26 VDC supply, drawing up to 12 W at 24 VDC. Power and status LEDs indicate the state of the board and its limit and home signals. The board is rated for an operating temperature of -20 ~ +75 °C.ApplicationsTwo-axis positioning of stepper or servo motors with ICP DAS motion controllersMotion control with Mitsubishi MELSERVO-J2 servo amplifiersAxis wiring where connector-based axis reassignment is required