PISO-725U Universal PCI Card, 8-ch Relay Output and 8-ch Isolated DI
PCI card with 8 Form C electromechanical relay outputs and 8 optically isolated digital inputs, supporting 3.3 V/5 V PCI slots and state-change interrupts on all inputs.
- Universal PCI interface supporting 3.3 V and 5 V PCI bus signalling
- 8 electromechanical Form C relay outputs with status readback and onboard LED indicators
- 8 optically isolated digital inputs with 3750 Vrms photo-isolation
- Jumper-selectable isolated or non-isolated digital inputs
- State-change interrupt on all digital inputs, removing the need for continuous polling
- Card ID switch to identify individual boards when using two or more cards in one computer
227,00 EUR per piece
| 1-9 pcs | 227,00 EUR | |
|---|---|---|
| 10-30 pcs | 216,00 EUR | −5 % |
| 31+ pcs | 205,00 EUR | −10 % |
Termékinformációk "PISO-725U Universal PCI Card, 8-ch Relay Output and 8-ch Isolated DI"
The PISO-725U is a universal PCI digital I/O board for PCs that need both switched control outputs and isolated contact sensing. It fits 3.3 V and 5 V PCI slots and combines eight electromechanical relay channels with eight optically isolated digital inputs on a single card.
The relay channels suit circuits that must be driven from a low-power control signal with full electrical separation, or where one signal has to switch several circuits. Relay status can be read back in software, and onboard LEDs show each channel's state. All relays are de-energised at power-on.
The digital inputs have 3750 Vrms photo-isolation and can be set by a hardware jumper to isolated or non-isolated operation. Every input generates an interrupt on a state change, so contact closures and openings can be detected without continuous polling. A Card ID switch lets software identify each board when two or more cards are installed in one computer. The card is supplied with one CA-4002 D-Sub connector.
Applications
- Factory automation
- Product test
- Laboratory automation
- Contact closure monitoring
- External voltage sensing
- Load sensing
- I/O control
| Product type: | PCI digital I/O board |
|---|---|
| Interface: | PCI |
| Digital inputs: | 8 |
| Relay outputs: | 8 |
| Ports: | 1 |
| Isolation: | 3750 Vrms |
| Power input: | 300 mA @ +5 V |
| Operating temperature: | 0 ~ +60 °C |
| Mounting: | PCI slot |
Specifications
| Hardware | |
|---|---|
| Connector | Female DB37 x 1 |
| Digital Input | |
| Channels | 8 (Photocoupler) |
| Sink/Source (NPN/PNP) | Sink |
| ON Voltage Level | 9 ~ 24 V |
| OFF Voltage Level | 0 ~ 1 V |
| Response Speed | 4 kHz (Typical) |
| Trigger Mode | Static Update |
| Isolation | 3750 Vrms (Using external power) |
| Relay Output | |
| Channels | 8 |
| Type | Form C |
| Contact Rating | AC: 0.3 A/120 V DC: 1 A/30 V |
| Operate Time | 5 ms (Typical) |
| Release Time | 10 ms (Typical) |
| PC Bus | |
| Type | 3.3 V/5 V Universal PCI, 32-bit, 33 MHz |
| Data Bus | 8-bit |
| Power | |
| Consumption | 300 mA @ +5 V |
| Mechanical | |
| Dimensions (mm) | 110 x 150 x 22 (W x L x D) |
| Environment | |
| Operating Temperature | 0 ~ +60°C |
| Storage Temperature | -20 ~ +70°C |
| Humidity | 5 ~ 85% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Bejelentkezés
Tartozékok
DB37 Male to Male Cable, 90º, 1M.
DB37 Male to Male Cable, 1M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 1.5M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 3M.
DB37 Male to Male Cable, Thin Monolithic Design, 5M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 5M.
The DB-37 CR is a screw terminal breakout board for connecting field wiring to a DAQ I/O board fitted with a 37-pin D-sub connector. It gives engineers a convenient termination point at the 5.08 mm pitch, so signals can be wired and serviced without working directly on the I/O connector.Each terminal maps pin for pin to the 37-pin D-sub interface, which simplifies cable planning and fault finding during commissioning. The board is rated for a maximum current of 1 A and a maximum DC voltage of 50 V, with a dielectric withstanding voltage of 250 VAC for one minute.Measuring 130 mm x 78 mm, the board is specified for an operating range of 0~ +60 °C and a storage range of -30 ~ +80 °C, with humidity of 10% ~ 90%, no condensing. It carries CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsField wiring for DAQ I/O boards with 37-pin D-sub connectorsTerminating signals for data acquisition systems
The DN-37 CR is a female DB37 to screw terminal board for wiring field signals to DB37-based data acquisition hardware. It provides two 37-pin D-sub connectors, one of which is intended for expansion, and two 19-pin screw terminal blocks with a 5.08 mm pitch, mounted on a DIN-rail.This ordering code includes a CA-3710 cable, a DB37 male-to-male, 45º, 1 m assembly, so the board can be connected to a compatible DB37 device straight out of the box. The board is rated for up to 1 A and 50 V DC, with a dielectric withstanding voltage of 250 VAC for one minute.Measuring 144 mm x 72 mm, the board is suited to control cabinets where a DIN-rail footprint is required. It is specified for an operating range of 0 ~ 60°C and carries CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsField wiring for DB37-based data acquisition boardsScrew terminal breakout in DIN-rail control cabinets
Hasonló termékek
The PISO-730AU CR is a universal PCI card that combines two digital I/O groups on one board: 16 optically isolated input and 16 isolated PNP output channels, plus 16 TTL input and 16 TTL output channels. It suits engineers who need to switch or sense field signals on a PC without a direct electrical connection between the host and the wiring.The isolated channels provide 3750 Vrms isolation, which helps break ground loops and shields the host computer from voltage spikes. Each isolated output is rated at 100 mA at +30 V per channel at 100% duty, and the outputs are open-emitter PNP type. The board is supplied with one CA-4002 D-Sub connector for field wiring.Supports 3.3 V and 5 V universal PCI slots (32-bit, 33 MHz)Static update trigger mode with 4 kHz typical response on isolated channelsTwo interrupt sources and a 4-bit card ID for multi-card systemsApplicationsFactory automationProduct testLaboratory automation
PISO-730AU-5V CR is a universal PCI card providing 32 optically isolated digital I/O channels (16 inputs and 16 outputs) alongside 32 TTL-level digital I/O channels (16 inputs and 16 outputs). It suits engineers who need galvanically separated signals next to direct logic-level connections on one host PC.The isolated inputs and outputs use optocouplers rated at 3750 Vrms, so field signals can float relative to the host ground. This prevents ground loops and shields the computer from damaging voltage spikes. Each isolated output includes an integral suppression diode for inductive loads, which makes the channels practical for alarms, signal switching and driving external circuits that need a higher voltage level.This ordering code includes one CA-4002 D-Sub connector. The card is intended for factory automation, product test and laboratory automation work.ApplicationsFactory automationProduct testLaboratory automation
The PISO-730U CR is a universal PCI card for engineers who need both opto-isolated and TTL-level digital I/O in one slot. It has 16 isolated digital inputs, 16 isolated open-collector outputs (NPN sink), and 16 TTL digital inputs and 16 TTL digital outputs, on a 32-bit, 33 MHz PCI bus.The isolated channels are rated at 3750 Vrms, which keeps field wiring electrically separate from the host PC and helps prevent ground loops. The isolated outputs include a Darlington (NPN) transistor and an integrated suppression diode for inductive loads, and the outputs can be read back at register level. A 4-bit SMD Card ID switch lets software identify each board when two or more cards are fitted in one computer.This ordering code includes one CA-4002 D-Sub connector. Drivers and development support cover Linux, DOS and Windows, with a DLL, ActiveX control and sample programs for several languages including C#.NET, Visual Basic.NET and LabVIEW.ApplicationsFactory automationProduct testLaboratory automation
The PISO-730U-5V is a universal PCI digital I/O card that fits both 3.3 V and 5 V PCI bus slots. It combines 32 optically isolated channels, comprising 16 digital inputs and 16 open-collector outputs (Sink, NPN), with 32 non-isolated 5 V/TTL channels, comprising 16 digital inputs and 16 outputs.The isolated channels are rated at 3750 Vrms, which lets field signals be floated to avoid ground loops and keeps the host computer protected from high voltages. Each isolated output uses a Darlington (NPN) transistor with an integrated suppression diode for inductive loads, making the card suitable for alarm signalling, output control and driving external circuits that need a higher voltage level.An onboard 4-bit Card ID switch lets software identify each board when two or more cards are installed in one computer. The card ships with one CA-4002 D-Sub connector.ApplicationsFactory automationProduct testLaboratory automation