Switches & Networking

The FSM-510G-2F CR is a Layer 2 Plus managed switch for Ethernet networks that need Gigabit copper ports, fibre uplinks and centralised control. It combines eight RJ-45 ports at 10/100/1000 Mbps with two SFP slots for 100 or 1000 Mbps fibre modules.Configuration is available over an RS-232 console, Telnet or a web-based interface, and SNMP allows the switch to be monitored and controlled remotely. QoS, VLAN, port trunking, port security and port mirroring help engineers segment traffic, prioritise critical data and tighten access control on high-bandwidth segments.Ring redundancy with STP and RSTP provides fail-over in under 20 ms, and IGMP v1/v2/v3 snooping and proxy support keep multicast traffic under control. This ordering code includes a console cable and a wall mount kit, and the switch can be installed on a DIN rail or on a wall.ApplicationsIndustrial communication networksHigh-bandwidth Ethernet segments that require VLAN segmentation and QoS

The iNS-306 CR is a six-port Ethernet switch that acts as a Power Sourcing Equipment (PSE) on ports 1 to 4. It centralises power distribution for IEEE 802.3af and 802.3at powered devices, delivering up to 30 W per port from a single DC supply.Each PoE port can be switched on and off remotely through the built-in web interface, which also reports Ethernet status and PoE voltage, current and consumption. Individual power on/off and reset schedules help reduce energy use and keep attached devices running reliably without site visits.For daisy-chained networks, ports 5 and 6 bypass the Ethernet signal if the switch loses power, helping important data continue to flow. Dual DC inputs with reverse polarity protection allow a backup supply to take over automatically.ApplicationsPowering IEEE 802.3af/at compliant powered devices from a central DC supplyRemote on/off and reset control of PoE-powered devicesEnergy saving through scheduled power-down of unused devicesDaisy-chained Ethernet installations requiring bypass during power failure

The iNS-308 CR is an 8-port Ethernet switch that combines PoE (PSE) power delivery with IoT management. Each of its eight RJ-45 ports can supply up to 30 W to a powered device, with support for IEEE 802.3af and 802.3at, so it suits installations where data and power must reach field devices over a single cable.Power is managed per port. Each PoE port has its own power on/off schedule and a separate reset schedule, which lets engineers switch off idle devices to save energy or restart devices that slow down over time. The web GUI shows Ethernet status along with PoE voltage, current and consumption, and the unit supports SNMP v2c, Modbus and MQTT for integration with monitoring systems.The switch accepts two DC supplies from 24 to 57 VDC, so a backup source takes over if the other fails. Ports 7 and 8 provide Ethernet bypass for daisy-chain layouts, keeping signal transmission running when the unit loses power. For total PoE loads above 60 W, the source recommends a dual input power supply.ApplicationsPowering and remotely power-cycling PoE devices in distributed installationsEnergy-saving control of PoE devices through scheduled power off and onDaisy-chain Ethernet networks where Ports 7 and 8 bypass the signal during a power failureIoT and industrial network nodes that need SNMP, Modbus or MQTT integration

iNS-316 CR is a 16-port IoT switch with 16 RJ-45 10/100Base-TX ports, all PoE/PoE+ PSE capable and compliant with IEEE 802.3af/at. Each port can supply up to 30 W from a 48 to 57 VDC power input, making it suited to powering cameras and other remote PoE devices from a single switch cabinet.Each PoE port has its own power on/off schedule and power reset schedule, so devices can be switched off when not needed to save energy, or cycled regularly to keep them running well. The built-in web GUI shows Ethernet status along with PoE voltage, current and consumption. Ports 15 and 16 support Ethernet bypass through daisy chaining, so the data path is maintained if the unit loses power.Dual power inputs can be connected to live DC sources at the same time, so the unit keeps running if one supply fails. The manufacturer recommends a dual input supply when total PoE load exceeds 60 W. With SNMP v2c, Modbus and MQTT support, the switch can also be integrated into monitoring and control systems, and it includes a relay alarm output.ApplicationsFactory AutomationRemote PoE Power ManagementWeb Camera Monitoring System

The iNS-3224-SFP CR is a 1U rack-mountable IoT switch that supplies IEEE 802.3af/at power to up to 24 PoE devices. Each port can deliver up to 30 W, and the web GUI shows Ethernet status, PoE voltage, current and consumption for every port.Power is managed per port. Engineers can set individual on/off schedules to switch powered devices off when they are not needed, and separate reset schedules to restart devices at regular intervals, both configured through a browser.Two redundant DC inputs (48 ~ 57 VDC) allow a backup source to take over automatically if one fails. Ports 1 and 2 provide Ethernet bypass for daisy-chain links, keeping signal transmission running during a power failure. The unit also offers Modbus function support and SNMP v2c.ApplicationsRemote power cycling and scheduled power control of PoE end devicesEnergy saving by switching off PoE devices outside working hoursPowering and monitoring PoE devices across a distributed networkDaisy-chain Ethernet links that must survive a power failureInstallations requiring redundant DC power supply

5 Pins M12 A Code Assembly Plug (Female).

4 Pins M12 D Code Assembly Plug (Male).

MSM-508 CR is an 8-port Layer 2 managed Industrial Ethernet switch for control and automation networks. Its eight RJ-45 ports support 10/100Base-TX with auto negotiation and automatic MDI/MDI-X, so connections can be made without crossover cables.The switch can be configured through the RS-232 console, or over Telnet or a web browser via the Ethernet ports. Managed functions include 802.1Q tag-based VLAN, port-based VLAN, 802.1p QoS, port trunking, spanning tree, cable testing and port mirroring. Built-in Cyber-Ring technology allows several switches to be formed into a redundant ring, with copper link failures detected and recovered in approximately 20 ms.Status of the Ethernet ports can be read by SCADA systems using Modbus/TCP, Modbus/RTU or OPC. Two DC power inputs (+12 ~ +48 VDC) can be connected at the same time, with the second source taking over if the first fails, and a relay output signals power or network link failure. The unit operates from -40 °C to +75 °C.ApplicationsIndustrial control and automation networksSCADA monitoring of Ethernet port statusRedundant Ethernet ring topologies

The MSM-508FC-T CR is an 8-port Layer 2 managed industrial Ethernet switch with six RJ-45 10/100Base-TX ports and two multi-mode 100Base-FX fibre ports fitted with SC connectors. Routing data over fibre keeps the transmission path immune to EMI and RFI and isolated from electrical exposure, surges, lightning and chemical corrosion, which makes it suited to links that must stay protected.The switch can be configured through an RS-232 console port or remotely over Telnet or a web browser. Its managed feature set includes 802.1Q tag-based and port-based VLANs, 802.1p QoS, port trunking, Spanning Tree, cable testing and port mirroring. The built-in Cyber-Ring technique lets several switches form a redundant ring that recovers from a fibre or copper link failure in approximately 20 ms.Two DC power inputs from +12 VDC to +48 VDC can be connected at the same time, so the second source takes over if the first fails. A relay alarm output signals power or network link failures, and Modbus/TCP, Modbus/RTU and OPC support allow a SCADA system to monitor the status of the Ethernet and fibre ports.ApplicationsEthernet links that must be protected from electrical exposure, surges and lightningRedundant ring networks with automatic link failure recoverySCADA and remote monitoring of Ethernet and fibre port status via Modbus or OPCIndustrial automation networks requiring managed Layer 2 switching with fibre backbone links

The MSM-508FCS-60T is an industrial Layer 2 managed switch that carries Ethernet traffic over single-mode fiber, so links are immune to EMI/RFI and electrical surges. It suits runs where the transmission path must be kept electrically isolated from the plant, with reach up to 60 km on the SC fiber ports.Management is available through an RS-232 console or over Ethernet via Telnet or a web browser. Managed features include 802.1Q tag-based and port-based VLANs, 802.1p QoS, port trunking, spanning tree, cable testing and port mirroring. The built-in Cyber-Ring technique allows several switches to form a redundant ring, with recovery from a fiber or copper link failure in approximately 20 ms.Two DC inputs can be connected to live sources at the same time, so the unit keeps running if one supply fails. A relay alarm output signals power or network link failures, and Modbus/TCP, Modbus/RTU and OPC let a SCADA system read the status of the Ethernet and fiber ports.ApplicationsLong-distance industrial Ethernet links where fibre immunity to EMI/RFI and surges is requiredRedundant ring networks for plant and process communicationSCADA monitoring of network and power status via Modbus or OPC

MSM-508FCS-T is an 8-port industrial Ethernet Layer 2 managed switch with two single-mode 100Base-FX fibre ports using SC connectors. Because data travels over fibre optic links, transmission is immune to EMI and RFI. It suits installations where the network must be kept clear of electrical exposure, surges, lightning and chemical corrosion.The switch can be configured through its RS-232 console port or over Ethernet using Telnet or a web browser. Its management feature set includes 802.1Q tag-based VLAN, port-based VLAN, 802.1p QoS, port trunking, spanning tree, cable testing and port mirroring. The built-in Cyber-Ring technique allows several switches to be arranged in a redundant ring, typically recovering from a fibre or copper link failure in approximately 20 ms.Two DC power inputs can be connected at the same time, so a failed supply is covered by the second live source. A relay alarm output signals power or network link failures, and Modbus/TCP, Modbus/RTU and OPC support allow a SCADA system to monitor the status of the Ethernet and fibre ports. This ordering code includes a CA-090510 console cable and a 4SIX1K0000003 wall mount.ApplicationsIndustrial Ethernet backbones where transmission must be protected from electrical exposure, surges, lightning or chemical corrosionRedundant ring networks requiring fast link-failure recoverySCADA systems monitoring Ethernet and fibre port status over Modbus or OPC

The MSM-508FT-T is an 8-port Layer 2 managed switch that pairs six RJ-45 10/100Base-TX ports with two multi-mode 100Base-FX ST fibre ports. Fibre transmission is immune to EMI and RFI, which makes it a good choice where links must be kept clear of electrical exposure, surges, lightning or chemical corrosion.The switch can be configured through its RS-232 console or over Ethernet using Telnet or a web browser. Managed functions include 802.1Q tag-based VLAN, port-based VLAN, 802.1p QoS, port trunking, spanning tree, cable testing and port mirroring. Built-in ICP DAS Cyber-Ring technology lets several switches form a redundant ring that recovers from a fibre or copper link failure in approximately 20 ms.Two DC power inputs (+12 VDC to +48 VDC) can be connected to live sources at the same time, so one source takes over if the other fails. A relay output signals power or network link failures, and Modbus/TCP, Modbus/RTU and OPC let a SCADA system monitor the status of the Ethernet and fibre ports.ApplicationsEthernet links that must be electrically isolated from surges, lightning or ground differencesInstallations exposed to chemical corrosion or EMI/RFIRedundant ring networks with fast link-failure recoverySCADA monitoring of network and fibre port status via Modbus or OPC

The NS-105A CR is an unmanaged 5-port Industrial Ethernet switch for connecting up to five workstations or devices over 10/100Base-TX. Each port auto-negotiates its speed between 10 Mbps and 100 Mbps and its flow control mode, and auto MDI/MDI-X lets you use either straight or crossover cables without configuration.Store-and-forward switching with IEEE 802.3x and back pressure flow control suits engineers who need a simple, compact switch on a DIN rail. Each port has activity, link and data rate LEDs to help with fault finding, and the shielded RJ-45 connectors are provided for each port.The switch accepts a wide +12 VDC to +53 VDC input and includes reverse polarity protection, a soft start function, overload protection and high-low voltage protection. It is rated for operating temperatures from -40 °C to +75 °C and is supplied in a slim plastic housing measuring 76 x 118 x 38 mm.ApplicationsConnecting up to five workstations or devices in industrial Ethernet networksCompact DIN-rail installations where a wide DC supply voltage range is needed

The NS-105PSE centralises power distribution for Ethernet-connected devices. Four of its five RJ-45 ports act as IEEE 802.3af power sourcing equipment, so PoE powered devices can be supplied over the same cable that carries their data, without a separate local supply at each device.Each PoE channel delivers up to 15.4 W, with automatic detection and power management. The switch runs store-and-forward wire-speed switching with IEEE 802.3x flow control and a 2048-entry MAC table, and it is isolated to 1500 Vrms for one minute. The plastic casing is designed for DIN-rail mounting and is rated for -40 °C to +75 °C operation.Four PoE PSE ports, each up to 15.4 W, for powering IEEE 802.3af compliant devicesUnmanaged switching across five 10/100Base-TX RJ-45 portsWide +46 to +55 VDC power input with reverse polarity protectionCompact DIN-rail housing, 76 x 118 x 38 mm (W x L x H)ApplicationsCentralised power distribution to PoE powered devices over EthernetIndustrial Ethernet networks requiring PoE-powered end devices

The NS-200AFC-T CR converts a 10/100 Base-TX copper Ethernet connection into a 100 Base-FX multi-mode fibre link, with one RJ-45 port on the copper side and one SC connector on the fibre side. It suits industrial Ethernet runs that need a copper-to-fibre transition inside a control cabinet or along a plant network.On the Ethernet side the converter negotiates 10/100 Mbps speed automatically and switches between MDI and MDI-X automatically, so straight or crossover cables can be used without configuration. It uses store-and-forward switching, supports IEEE 802.3x flow control and includes reverse polarity protection on its power input. The fibre port is specified for 2 km over multi-mode fibre, with 62.5/125 μm recommended for full duplex operation.The housing is plastic with DIN-rail mounting and measures 33 x 107 x 78 mm (W x L x H). It is rated for operation from -30 °C to +75 °C and storage from -30 °C to +85 °C, at 10% to 90% RH non-condensing. The power input accepts +12 to +48 VDC and is non-isolated.ApplicationsExtending industrial Ethernet links from copper to multi-mode fibreConnecting copper-based devices to a fibre backbone in control cabinets and plant networks

NS-200AFCS-60T is an industrial media converter that bridges a copper 10/100Base-TX Ethernet segment and a 100Base-FX single-mode fibre link with an SC connector, rated for 60 km. It suits engineers who need to extend an Ethernet connection over a long fibre run without changing the connected equipment.The RJ-45 port negotiates 10 or 100 Mbps automatically and detects MDI/MDI-X wiring itself, so it can be installed without crossover cables. The store-and-forward design handles traffic between the two media, and reverse polarity protection guards the power input.The unit accepts a wide +12 to +48 VDC supply and runs from -30 to +75 °C. Its slim plastic housing mounts on a DIN rail, and the status LEDs show power, speed, link activity and fibre duplex mode.ApplicationsExtending industrial Ethernet links over single-mode fibre up to 60 kmConnecting RJ-45 equipment to a fibre backbone in DIN-rail mounted control panels

NS-200AFCS-T bridges a copper Ethernet segment and a single-mode fibre link, letting engineers extend industrial Ethernet networks over distances of up to 30 km. The RJ-45 port handles 10/100 Mbps with auto negotiation and automatic MDI/MDI-X, so it can be connected without concern for cable wiring or port polarity.The converter uses a store-and-forward architecture with 1024 MAC table entries and IEEE 802.3x flow control. The fibre side uses an SC connector and supports 8.3/125, 8.7/125, 9/125 or 10/125 μm single-mode cable at a wavelength of 1300 or 1310 nm.Built for control cabinets, it has a plastic housing and a slim profile for DIN-rail mounting. It operates from -30 ~ +75 °C and accepts +12 ~ +48 VDC with reverse polarity protection. The ordering code NS-200AFCS-T CR is the RoHS-compliant version.ApplicationsExtending industrial Ethernet links over single-mode fibreConnecting remote Ethernet devices to a fibre backbone in control cabinets

NS-200AFT-T bridges a copper Ethernet segment and a multi-mode fibre link. The RJ-45 port runs at 10 or 100 Mbps with auto negotiation and automatic MDI/MDI-X, so it can be connected to a switch or a device without choosing a crossover cable. The fibre side uses a 100Base-FX multi-mode ST connector, suited to extending an Ethernet connection across the distances covered by the fibre specification.The converter uses store-and-forward processing with wire-speed switching and supports IEEE 802.3, 802.3u and 802.3x, including flow control. Reverse polarity protection is fitted on the power input, which accepts +12 VDC to +48 VDC (non-isolated). Power consumption is 0.12 A at 24 VDC.The plastic housing is slim enough for DIN-rail mounting and is rated for an operating temperature of -30 °C ~ +75 °C, with a storage range of -30 °C ~ +85 °C. Status LEDs show power, 10M and 100M speed, link/activity and the fibre duplex state. The product is listed with CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsExtending 10/100Base-TX Ethernet connections over 100Base-FX multi-mode fibre in industrial installationsConnecting copper-based Ethernet devices to a fibre backbone in cabinets with a DIN-rail footprint

The NS-200PS CR is a Powered Device (PD) that takes a Power over Ethernet feed from a PSE and separates it into an Ethernet data connection and a 24 VDC power output. It lets a single cable to the cabinet supply both the network link and the power for a nearby device.Power is detected and classified automatically, and it is accepted from either the signal pairs or the unused pairs. The output is isolated and protected against short circuits, with a rated 10 W at 24 VDC (0.42 A). The slim plastic housing measures 33 x 107 x 78 mm (W x L x H) and mounts on a DIN rail.Rated for operating temperatures from -40 °C to +75 °C, the unit is certified to CE, UKCA, FCC, RoHS and WEEE. Specified standards are IEEE 802.3, 802.3u, 802.3x and 802.3af.ApplicationsPowering 24 VDC industrial devices over the Ethernet cableProviding an Ethernet connection and power to remote devices from a single PoE source

NS-200WDM-A is the local-end unit of a single-strand fibre media converter pair. It bridges a 10/100Base-TX RJ-45 Ethernet port to a 100Base-FX SC fibre link, carrying both transmit and receive traffic over one single-mode fibre using wavelength division multiplexing (TX 1310 nm, RX 1550 nm). This halves the number of fibres needed for a link, which is useful where long-distance fibre is costly to install.The unit is designed for plug-and-play use, with automatic MDI/MDI-X crossover and 10/100 Mbps auto negotiation. It uses store-and-forward switching and provides 1500 Vrms isolation. Overload protection, soft start, high/low voltage protection and reverse polarity protection are included. Its 32.3 mm width suits compact DIN-rail installations.Important: this unit works as a pair. You must order NS-200WDM-A together with NS-200WDM-B at the other end of the link.ApplicationsExtending 100 Mbps Ethernet over long-distance single-mode fibreReducing fibre infrastructure cost by reusing a single strandSpace-constrained control cabinets and DIN-rail installations

The NS-200WDM-B is a single-strand fibre media converter that carries Ethernet over one single-mode fibre instead of two. Wavelength division multiplexing sends two independent data channels along the same strand, with this unit transmitting at 1550 nm and receiving at 1310 nm. It is well suited to extending Ethernet links over longer distances where fibre installation is costly.The NS-200WDM-B works only as a pair with the NS-200WDM-A, which must be installed at the opposite end of the link. The unit uses store-and-forward switching, automatic MDI/MDI-X crossover and IEEE 802.3x full duplex flow control, so it can be connected without special cabling. A soft start function, overload protection and high-low voltage protection are included, and a reverse polarity protected +12 ~ +48 VDC supply simplifies installation on DIN-rail equipment racks.Ordering code NS-200WDM-B CR is the TX 1550 nm / RX 1310 nm side of the series. Specify the matching NS-200WDM-A when ordering to ensure both ends of the link are compatible.ApplicationsExtending Ethernet connections over long single-mode fibre linksReducing fibre infrastructure cost by running two channels over one strandConnecting remote Ethernet devices to a network across a fibre backbone

The NS-205-IP67 is an unmanaged five-port Ethernet switch for industrial networks installed in harsh environments. Its housing carries an IP67 protection rating, and the RJ-45 connectors are built to hold reliable connections where vibration and shock are present.Each port auto-negotiates 10 or 100 Mbps and runs in full- or half-duplex mode, with automatic MDI/MDI-X crossover for plug-and-play installation. Traffic is switched store-and-forward at wire speed, supported by a 1024-entry MAC table and 256 Kbit of frame buffer memory. IEEE 802.3x full-duplex flow control and half-duplex backpressure are both available.The protection grade determines the operating envelope. IP67 applies from -10 °C to +60 °C at up to 100% RH, while IP66 applies from -40 °C to +75 °C at 10% to 90% RH, non-condensing. Power comes from a +10 to +30 VDC input with reverse polarity protection and 1 kV isolation, drawing 0.12 A at 24 VDC.ApplicationsIndustrial Ethernet networks in harsh environmentsInstallations subject to high vibration and shock

The NS-205A CR is an unmanaged industrial Ethernet switch with five 10/100Base-TX RJ-45 ports. It uses store-and-forward processing with wire-speed switching, and each port auto-negotiates its speed and flow control, so it can be connected to a network without manual configuration.Automatic MDI/MDI-X crossover means straight or crossed cables can be used. Each port has activity, link and data rate LEDs to help with fault finding, and the shielded RJ-45 connectors suit installations where cable screening matters. The 33 mm width keeps the unit compact where DIN-rail space is tight.The power input accepts +12 VDC to +56 VDC and includes reverse polarity protection, soft start, overload protection and high-low voltage protection. The switch operates from -40 °C to +75 °C and is certified to CE, UKCA, FCC, RoHS and WEEE.ApplicationsConnecting up to five workstations or devices on a 10/100 Mbps Ethernet networkIndustrial control cabinets where DIN-rail space is limitedWide-voltage DC installations supplied from +12 VDC to +56 VDC sources

NS-205AFC-T CR is an unmanaged Ethernet switch that combines four 10/100Base-TX RJ-45 ports with one 100Base-FX multi-mode fibre port terminated in an SC connector. The fibre link keeps electrical noise away from the signal path and extends reach to 2 km in full duplex, which suits connections between cabinets or buildings where copper would be unreliable.The switch accepts redundant +12 to +48 VDC supplies, so it can run from common industrial DC rails without an external converter. Reverse polarity protection and a relay alarm output rated 2 A @ 30 VDC help with fault monitoring on site.Store-and-forward processing, IEEE 802.3x flow control and broadcast storm protection support stable operation on small industrial Ethernet segments. Mounting is on DIN-rail, and the operating range is -30 °C to +75 °C.ApplicationsIndustrial Ethernet segments requiring a fibre link for noise immunityFibre uplinks between cabinets or buildings for Ethernet-connected equipmentInstallations with a 12 to 48 VDC power supply and no external converter