DB-37 DB37 to Screw Terminal Board, 37-pin D-sub, 5.08 mm Pitch
DB-37 CR breakout board that takes a 37-pin D-sub DAQ I/O connector to screw terminals on 5.08 mm pitch, rated 1 A max and 50 V DC max.
- 37-pin D-sub to screw terminal conversion, pin to pin with a 37-pin D-sub DAQ I/O board
- 5.08 mm terminal pitch
- Current rating 1 A max.
- DC rating 50 V max.
- Dielectric withstanding voltage 250 VAC for 1 minute
- Board size 130 mm x 78 mm
56,00 EUR per piece
| 1-9 pcs | 56,00 EUR | |
|---|---|---|
| 10-30 pcs | 53,00 EUR | −5 % |
| 31+ pcs | 51,00 EUR | −9 % |
Termékinformációk "DB-37 DB37 to Screw Terminal Board, 37-pin D-sub, 5.08 mm Pitch"
The DB-37 CR is a screw terminal breakout board for connecting field wiring to a DAQ I/O board fitted with a 37-pin D-sub connector. It gives engineers a convenient termination point at the 5.08 mm pitch, so signals can be wired and serviced without working directly on the I/O connector.
Each terminal maps pin for pin to the 37-pin D-sub interface, which simplifies cable planning and fault finding during commissioning. The board is rated for a maximum current of 1 A and a maximum DC voltage of 50 V, with a dielectric withstanding voltage of 250 VAC for one minute.
Measuring 130 mm x 78 mm, the board is specified for an operating range of 0~ +60 °C and a storage range of -30 ~ +80 °C, with humidity of 10% ~ 90%, no condensing. It carries CE, UKCA, FCC, RoHS and WEEE certifications.
Applications
- Field wiring for DAQ I/O boards with 37-pin D-sub connectors
- Terminating signals for data acquisition systems
| Product type: | Screw terminal board |
|---|---|
| Interface: | 37-pin D-sub |
| Operating temperature: | 0~ +60 °C |
Specifications
| Mechanical | |
|---|---|
| Dimensions (mm) | 130 mm x 78 mm |
| Environment | |
| Operating Temperature | 0~ +60 °C |
| Storage Temperature | -30 ~ +80 °C |
| Humidity | 10% ~ 90%, no condensing |
Specifications as published by the manufacturer. Subject to change.
Bejelentkezés
Hasonló termékek
The DB-32R CR is a 32-channel Form A signal relay board that accepts a 37-pin connector to control 32 relays. It is intended for use with the PISO-C64 and ISO-C64, giving those modules a bank of relay switching channels on a DIN-rail mounted board.Each Form A relay is rated 250 VAC/30 VDC at 3 A for 100,000 operations minimum at 10 operations per minute, or 5 A for 6,000 operations minimum under the same conditions. Operate and release times are 10 ms typical, and the board is powered from +12 ~ 30 VDC, drawing 0.25 A at +24 V maximum.Suited to engineers who need relay outputs alongside a PISO-C64 or ISO-C64 setupOperating range of -25 ~ +75 °C with storage from -30 ~ +80 °CHumidity tolerance of 10% ~ 90%, non-condensingSupplied with the CA-3710D DB37 male to male cable, 180º, 1 mApplicationsRelay switching expansion for PISO-C64 and ISO-C64 systems
DB-12SSR is a daughter board that provides twelve AC solid-state relay outputs, each optically isolated from the control side. It plugs directly into an OPTO-22 compatible board, so engineers can add switched AC loads to an existing data acquisition setup without building a separate interface.Each channel shows its relay status on an LED, which helps with commissioning and fault finding. Field wiring is made on screw terminals. The board is supplied with the CA-5015 flat cable (50-pin, 1.5 m) for the connection to the host board.Relay operate time is specified at 1/2 cycle of the voltage sine wave, 1 ms maximum, and the solid-state design has no contact arcing or bounce. The board draws 400 mA at 5 V and is rated for an operating temperature of 0 ~ 60°C.ApplicationsOn/off controlEnergy managementTest automationProcess control
The DB-12SSR/D is a 12-channel AC solid-state relay daughter board for switching mains-level loads from a DAQ system. Each channel is a Form A SSR, and the board plugs directly into an OPTO-22 compatible board, so it can be added to an existing acquisition setup without custom wiring.Field wiring terminates on screw terminals, and an LED on each channel shows the relay state, which helps with commissioning and fault finding. Per the ordering information, this variant ships with a CA-3710 DB37 male-to-male cable (45º, 1 m) instead of the CA-5015 flat cable supplied with the base DB-12SSR.Typical uses include on/off switching, energy management, test automation and process control. The board operates from 0 to 60 °C and is stored between -20 and 70 °C, with humidity rated at 5 % to 90 % non-condensing.ApplicationsOn/off controlEnergy managementTest automationProcess control
The DB-12SSR/D/DIN provides 12 optically isolated AC solid-state relay channels on a board designed for DIN-rail mounting. It connects directly to an OPTO-22 compatible board, so engineers can switch AC loads from an existing digital I/O setup without building custom relay stages.Each channel has an LED that shows relay status, and field wiring is made through screw terminals. Each channel is rated at 4 A @ 240 VAC, with an operate time of 1/2 cycle of the voltage sine wave, 1 ms maximum. The board draws 400 mA @ 5 V and measures 223.5 mm x 135.5 mm.This variant is supplied with the CA-3710 cable (DB37 male to male, 45º, 1 M). It suits on/off control, energy management, test automation and process control applications. The operating range is 0 ~ 60°C, with storage from -20 ~ 70°C and 5% to 90% humidity, non-condensing.ApplicationsOn/off controlEnergy managementTest automationProcess control