X324 X-board, 4-ch 0 ~ 5 V Analog Output and 4-ch Digital Output

The X400 CR is a timer/counter X-board that extends the I-7188XC with three 16-bit channels. It suits engineers who need pulse counting and timing functions on a compact add-on board rather than a separate I/O module.Each of the three channels is non-isolated, so the board is best suited to installations where the signal sources share a suitable ground reference. The X400 CR is specified at 0.3 W consumption and a 38 mm x 64 mm footprint. Note that only one X-board can be fitted to each µPAC.Rated for an operating range of -25 ~ +75 °C, storage from -40 ~ +80 °C and 5 ~ 90 % humidity, non-condensing, the X400 CR carries CE, UKCA, RoHS and WEEE marks.ApplicationsPulse counting and timing on I-7188XC systems

The X308 CR is an X-board that extends compatible I-7188 and uPAC-7186EX controllers with four non-isolated analogue inputs and six digital outputs. Each input reads 0 ~ +10 V at 12-bit resolution, with a sampling rate of up to 1 KHz, which suits engineers who need simple voltage acquisition alongside switching on a single controller.The digital outputs are open-collector (NPN) with a load voltage of up to +30 VDC and a 100 mA load current. The analogue inputs offer 2 MOhm input impedance and ±30 VDC overvoltage protection. Both I/O groups are non-isolated, so this board is best suited to installations where isolation is provided elsewhere in the system.The X308 CR is compatible with the I-7188XB, I-7188XG, I-7188EX, I-7188EG and uPAC-7186EX series. Only one X-board can be fitted to each µPAC. The board measures 38 mm x 64 mm, operates from -25 ~ +75 °C and is RoHS and WEEE certified.ApplicationsVoltage signal monitoring on µPAC and I-7188 controllersSwitching loads with NPN open-collector digital outputs

The X305D CR is a plug-in X-board that adds I/O to compatible uPAC-7186EX and I-7188 series controllers. It provides eight single-ended analogue current inputs covering 0 ~ 20 mA at 12-bit resolution, alongside two digital inputs and two digital outputs on the same board.The analogue inputs sample at up to 4 KHz and present a 125 Ohm input impedance, with overvoltage protection rated at ±30 VDC. The digital inputs detect dry contacts, and the outputs are open-collector sink (NPN) type rated for loads up to +30 VDC and 100 mA. All I/O circuits are non-isolated.Only one X-board can be fitted to each µPAC, so the X305D CR suits designs that need current-loop measurement and simple switching within the controller's footprint. The board is rated for an operating range of -25 ~ +75 °C and measures 38 mm x 64 mm.ApplicationsCurrent-loop (0 ~ 20 mA) measurement within supported uPAC-7186EX and I-7188 controllersLocal digital switching and contact sensing on compact control panelsExpansion of supported PAC systems with additional I/O using a single X-board slot

The X305 CR is a mixed I/O X-board for the I-7188XB, I-7188XG, I-7188EX, I-7188EG and uPAC-7186EX series. It provides seven 12-bit voltage analogue inputs and one 12-bit voltage analogue output, each spanning ±5 VDC, alongside two wet-contact digital inputs and two open-collector digital outputs. None of the channels are isolated.The analogue inputs have a 50 KOhm input impedance and tolerate overvoltage up to ±30 VDC, with a maximum sampling rate of 1 KHz. The digital inputs are sink type with an ON level of +3.5 V to +30 VDC, and the NPN open-collector outputs switch loads up to +30 VDC at 100 mA. Only one X-board can be fitted to each µPAC.The board measures 38 mm x 64 mm and is rated for an operating temperature of -25 ~ +75 °C, with storage from -40 ~ +80 °C and 5 ~ 90 % humidity, non-condensing. It carries RoHS and WEEE certification.ApplicationsAdding analogue and digital I/O to supported I-7188 and uPAC-7186EX controllersVoltage signal acquisition and analogue control within the ±5 VDC range

The X304 CR is an X-board that adds mixed analogue and digital I/O to supported I-7188 and uPAC-7186EX controllers. It provides three 12-bit analogue inputs and one 12-bit analogue output, each rated ±5 VDC, together with four digital inputs and four digital outputs, all without isolation.Engineers would choose the X304 CR when a compact controller needs voltage-based analogue measurement and control alongside discrete switching. The digital inputs accept wet contacts in sink configuration, and the digital outputs are NPN open-collector type rated up to 30 VDC and 100 mA per channel.The board is compatible with the I-7188XB, I-7188XG, I-7188EX and I-7188EG, and with the uPAC-7186EX series. Each µPAC accepts only one X-board. The module measures 38 mm x 64 mm and is specified for an operating range of -25 ~ +75 °C.ApplicationsAdding analogue and digital I/O to supported I-7188 and uPAC-7186EX controllersVoltage-based analogue measurement and control with discrete switching

The X303 is an X-board that adds analogue and digital I/O to compatible I-7188 and uPAC-7186EX controllers. It provides one 12-bit analogue input and one 12-bit analogue output, both rated ±5 VDC, together with four digital inputs and six digital outputs, all non-isolated.The X-board is designed for the I-7188XB, I-7188XG, I-7188EX, I-7188EG and uPAC-7186EX series. Only one X-board can be fitted to each µPAC controller.On the digital side, the inputs are wet-contact sink type with an ON level of +3.5 V to +30 VDC, while the outputs are NPN open collector rated for loads up to +30 VDC and 100 mA. The module measures 38 mm x 64 mm and is specified for operation from -25 to +75 °C.ApplicationsAdding analogue and digital I/O to compatible I-7188 and uPAC-7186EX controllers

The X302 adds basic voltage measurement and voltage output to an I-7188XC controller through a single X-board. It provides one 12-bit analogue input and one 12-bit analogue output, both rated ±5 VDC and both without isolation.The analogue input offers a maximum sampling rate of 900 Hz and a 50 KOhm input impedance, with overvoltage protection up to ±5 VDC. The analogue output can supply up to 10 mA, which suits driving a simple voltage-controlled device or signal input.Fits the I-7188XC series; one X-board can be fitted per µPAC.Compact 38 mm x 64 mm board with an operating range of -25 ~ +75 °C.ApplicationsVoltage measurement on I-7188XC controllersVoltage output control on I-7188XC controllers

The X301 adds one voltage analog input and one voltage analog output to the I-7188XC. Both channels are 12-bit and non-isolated, so the X301 suits projects that need to read a low-voltage signal and drive a control voltage from the same controller board.The input accepts 0 ~ 2.5 VDC and samples at up to 200 KHz, with a 1 KOhm input impedance and +30 VDC overvoltage protection. The output spans 0 ~ 4.095 V and can source up to 20 mA.The X301 is designed for the I-7188XC. The wider X-board range also covers other I-7188 and uPAC-7186 controllers, but the X301 itself is specified for the I-7188XC. Check the ordering code and controller model before fitting.ApplicationsAnalog voltage acquisition on I-7188XC systemsAnalog voltage output for control on I-7188XC systems

The X300 adds two analogue voltage outputs to a compatible controller through a plug-in X-board. Each channel uses a 12-bit D/A stage with an output range of 0 ~ 4.095 VDC, which suits control signals that need a simple, known voltage span.The X300 is specifically listed for the I-7188XC. The wider X-board series covers the I-7188XA, I-7188XB, I-7188XG, I-7188EG, I-7188EX and several uPAC-7186EX variants, so check the host model before ordering. Only one X-board can be fitted to each µPAC.Non-isolated outputs with a 5 mA voltage output capability per the source dataCompact 38 mm x 64 mm board footprintOperating range -25 ~ +75 °C, storage -40 ~ +80 °CApplicationsProviding 0 ~ 4.095 V analogue control outputs on an I-7188XC controller

The X310 CR is an X-board that adds local analogue and digital I/O to compatible I-7188 and uPAC-7186EX controllers. It suits projects that need current and voltage measurement alongside contact sensing and switched outputs on a single expansion board.Two 12-bit analogue inputs cover different signal types: channel 0 accepts 0 ~ 20 mA and channel 1 accepts 0 ~ +10 V. Three wet-contact digital inputs are configured as sink and switch on from +3.5 V to +30 VDC. A 12-bit analogue output provides 0 ~ +10 V with a 10 mA voltage output capability.The three digital outputs are open collector NPN type, rated for loads up to +30 VDC and 100 mA. All channels are non-isolated, and the board measures 38 mm x 64 mm. Only one X-board can be fitted to each µPAC unit.ApplicationsAdding analogue and digital I/O to compatible I-7188 and uPAC-7186EX controllers