I-8056W-G 16-ch Non-isolated Sink DO Module, 5~30 VDC

I-8056 CR is a 16-channel digital output module from the I-8K/I-87K low-profile series, suited to engineers who need to switch a bank of sink-type loads from a compact I/O node. Each of the 16 non-isolated open-collector channels is rated for a load voltage of +5 VDC to +30 VDC and up to 100 mA per channel.Channel status is visible at a glance, with one LED per output alongside a power and communication indicator. Each terminal is protected against ESD to ±4 kV contact (IEC 61000-4-2), which helps the module tolerate handling and electrostatic events during installation and maintenance.The CR suffix identifies the blue-cover version of the I-8056. Key electrical and environmental data are listed below for specification checks.Power consumption: 0.9 W max.Dimensions: 31 x 116 x 88 mm (W x L x H)Operating temperature: -25 ~ +75 °C; storage -40 ~ +85 °CHumidity: 10 ~ 90% RH, non-condensingApplicationsSwitching sink-type DC loads in the 5 to 30 VDC rangeDigital output expansion in I-8K/I-87K low-profile I/O systemsLocal monitoring of output channel status via LEDs

The I-8056-G CR is a 16-channel digital output module from the I-8K/I-87K low-profile series, suited to switching 5~30 VDC loads from a PAC or remote I/O system. Each channel is a sink-type (NPN) open collector output rated at 100 mA, so the module pulls the load to ground when a channel is active.Engineers choosing the gray-cover variant will find the same 16 non-isolated outputs, with a LED for each output channel plus one for power and communication, so channel state can be checked directly on the module during commissioning and fault finding. The DO channels carry 4 kV ESD protection (IEC 61000-4-2, contact, each terminal) as standard.The module draws a maximum of 0.9 W and is specified for an operating temperature of -25 ~ +75 °C, with a storage range of -40 ~ +85 °C. Its compact 31 x 116 x 88 mm (W x L x H) footprint makes it practical for dense control panels.ApplicationsSwitching 5~30 VDC loads from PAC or remote I/O systemsControl panels using the I-8K/I-87K low-profile series

The I-8050W-G CR provides 16 universal digital channels, each of which can be programmed as either a digital input or a digital output. This makes it a flexible choice where the I/O mix may change or is not fixed at the design stage.Every channel is photocoupler isolated. Inputs are sink-type with a +10 ~ +30 VDC ON level, and outputs are isolated open-collector sink drivers rated for a +5 ~ +30 VDC load at 100 mA per channel, with short-circuit protection. Power-on and safe values can be configured for the outputs.16 channels, each programmable as input or output3750 VDC intramodule isolation as standard±4 kV ESD protection on each terminalCE, FCC, RoHS and WEEE listedApplicationsInterfacing sink-type field switches and sensors to a controllerSwitching loads of up to 100 mA per channel with open-collector outputs in industrial control panels

The I-8051 CR is a 16-channel digital input module for reading dry contact switches over long cable runs. Each channel is read by connecting it to GND (ON) or leaving it open (OFF), so it suits simple switch, relay and push-button monitoring in panel and machine wiring.All 16 channels are non-isolated and each terminal has ±4 kV contact ESD protection to IEC 61000-4-2. A status LED for every input, plus one for power and communication, makes it straightforward to check field wiring and channel state during commissioning and fault finding.This variant is the blue-cover version. The I-8051-G is listed as a similar model in the same series.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment