ISO-DA8 ISA Isolated Analogue Output Board, 8-ch 14-bit AO
ISO-DA8 CR is an 8-channel, 14-bit isolated analogue output card for ISA bus PCs, with software-selectable voltage and 4 ~ 20 mA current outputs.
- 8-channel, 14-bit isolated analogue outputs on an ISA bus card
- Software-selectable unipolar or bipolar ranges (0 ~ 5 V, ±5 V, 0 ~ 10 V, ±10 V) and 4 ~ 20 mA current sink per channel
- 3000 VDC isolation from the built-in DC/DC converter and 2500 VDC photo-isolation protection
- Double-buffered D/A latch with power-on output values stored in EEPROM
- Jumperless, trimless design with software calibration data stored in EEPROM
- 16 digital inputs and 16 digital outputs at 5 V/TTL levels
698,00 € per piece
| 1-9 pcs | 698,00 € | |
|---|---|---|
| 10-30 pcs | 664,00 € | −5 % |
| 31+ pcs | 629,00 € | −10 % |
Informácie o výrobku "ISO-DA8 ISA Isolated Analogue Output Board, 8-ch 14-bit AO"
The ISO-DA8 CR is an ISA bus analogue output card for PC/AT compatible computers. It provides eight 14-bit channels with optical isolation rated for up to 2500 VDC common-mode voltage, so it suits programmable source and loop-driving tasks where field wiring must be kept apart from the PC.
Each channel can be configured in software as a voltage output or a 4 ~ 20 mA current sink. Output type (unipolar or bipolar) and range, covering 0 ~ 5 V, ±5 V, 0 ~ 10 V and ±10 V, are set by software. The card uses a double-buffered D/A latch and a command set for programming, and its calibration is performed in software with data stored in EEPROM, so there are no jumpers or trimpots to adjust.
The board also provides 16 digital inputs and 16 digital outputs at 5 V/TTL levels, plus three 16-bit timer/counter channels. A power-on value for each output can be predefined and held in the on-board EEPROM. A CA-4002 D-Sub connector is included, and the card draws 800 mA from +5 V with an operating range of 0 ~ +60°C.
Applications
- Programmable voltage source
- Programmable current sink
- Harsh environment operation
- Process control
| Product type: | Analog output board |
|---|---|
| Interface: | ISA bus |
| Digital inputs: | 16 |
| Digital outputs: | 16 |
| Analog outputs: | 8 |
| Isolation: | 2500 VDC |
| Power input: | 800 mA @ +5 V |
| Operating temperature: | 0 ~ +60 °C |
Specifications
| Hardware | |
|---|---|
| Connector | Female DB37 x 1 20-pin Box header x 2 |
| Analog Output | |
| Channels | 8 |
| Range | Voltage: ±10 V Current: 0 ~ 20 mA |
| Resolution | 14-bit |
| Accuracy | 0.04% of FSR ±2 LSB @ 25 °C, ± 10 V |
| Response Time | 250 kHz (Typical) |
| Voltage Output Capability | ±5 mA |
| Slew Rate | 0.6 V/μs |
| Operation Mode | Static Update |
| Digital Input | |
| Channels | 16 |
| Type | 5 V/TTL |
| ON Voltage Level | 2.0 V Min. |
| OFF Voltage Level | 0.8 V Max. |
| Response Speed | 1.0 MHz (Typical) |
| Trigger Mode | Static Update |
| Digital Output | |
| Channels | 16 |
| Type | 5 V/TTL |
| Operation Mode | Static Update |
| Load Voltage | Logic 0: 0.4 V Max. Logic 1: 2.4 V Min. |
| Load Current | Sink: 2.4 mA @ 0.8 V Source: 0.8 mA @ 2.0 V |
| Response Speed | 1.0 MHz (Typical) |
| Timer/Counter/Frequency | |
| Channels | 3 |
| Type | 5 V/TTL |
| Resolution | 16-bit |
| Reference Clock | Internal: 4 MHz |
| PC Bus | |
| Type | ISA |
| Data Bus | 8-bit |
| Power | |
| Consumption | 800 mA @ +5 V |
| Mechanical | |
| Dimensions (mm) | 122 x 182 x 22 (W x L x D) |
| Environment | |
| Operating Temperature | 0 ~ +60°C |
| Storage Temperature | -20 ~ +70°C |
| Humidity | 5 ~ 85% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Prihlásiť sa
Príslušenstvo
Flat Cable, 20-pin, 1M.
Flat Cable, 20-pin, 2M.
DB37 Male to Male Cable, 90º, 1M.
DB37 Male to Male Cable, 1M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 1.5M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 3M.
DB37 Male to Male Cable, Thin Monolithic Design, 5M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 5M.
DB37 connector Male with plastic cover (Solder Type).
The DB-37 CR is a screw terminal breakout board for connecting field wiring to a DAQ I/O board fitted with a 37-pin D-sub connector. It gives engineers a convenient termination point at the 5.08 mm pitch, so signals can be wired and serviced without working directly on the I/O connector.Each terminal maps pin for pin to the 37-pin D-sub interface, which simplifies cable planning and fault finding during commissioning. The board is rated for a maximum current of 1 A and a maximum DC voltage of 50 V, with a dielectric withstanding voltage of 250 VAC for one minute.Measuring 130 mm x 78 mm, the board is specified for an operating range of 0~ +60 °C and a storage range of -30 ~ +80 °C, with humidity of 10% ~ 90%, no condensing. It carries CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsField wiring for DAQ I/O boards with 37-pin D-sub connectorsTerminating signals for data acquisition systems
The DN-37 CR is a female DB37 to screw terminal board for wiring field signals to DB37-based data acquisition hardware. It provides two 37-pin D-sub connectors, one of which is intended for expansion, and two 19-pin screw terminal blocks with a 5.08 mm pitch, mounted on a DIN-rail.This ordering code includes a CA-3710 cable, a DB37 male-to-male, 45º, 1 m assembly, so the board can be connected to a compatible DB37 device straight out of the box. The board is rated for up to 1 A and 50 V DC, with a dielectric withstanding voltage of 250 VAC for one minute.Measuring 144 mm x 72 mm, the board is suited to control cabinets where a DIN-rail footprint is required. It is specified for an operating range of 0 ~ 60°C and carries CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsField wiring for DB37-based data acquisition boardsScrew terminal breakout in DIN-rail control cabinets
Podobné produkty
ISO-DA16/S CR is an ISA bus card that provides 16 isolated, double-buffered analogue outputs for PC/AT compatible computers. Each channel can be configured in software as a voltage output or a current sink, so one board can serve as a programmable voltage source or a programmable current sink in the same system.Isolation is provided by a built-in DC/DC converter rated at 3000 VDC, together with 2500 VDC photo-isolation. Output type (unipolar or bipolar) and range (0 ~ 5 V, ±5 V, 0 ~ 10 V or ±10 V) are set in software, and calibration is also performed in software with the data held in EEPROM, so no trimpots or jumpers need adjusting.The board also includes 16 digital inputs, 16 digital outputs at 5 V/TTL levels and three 16-bit timer/counter channels. It is supplied with a DN-37 terminal board and a CA-3710 D-Sub cable. Engineers working on process control or harsh-environment installations within the 0 ~ +60 °C operating range will find the board suited to these tasks.ApplicationsProgrammable voltage sourceProgrammable current sinkHarsh environment operationProcess control
The ISO-DA8/S CR is an isolated analog output card for PC/AT compatible computers, providing eight 14-bit channels that can drive voltage or current loads. Each channel has its own converter with built-in DC/DC isolation, which suits engineers who need to keep control outputs electrically separated from the host PC.Output type and range are set in software, so unipolar or bipolar operation and the 0 ~ 5 V, ±5 V, 0 ~ 10 V or ±10 V ranges can be changed without hardware adjustment. The board is jumperless and trimless, and calibration is performed in software with the data held in EEPROM. The power-on output value can also be defined and stored on board, which helps when outputs must start from a known state.The card also provides 16 digital inputs, 16 digital outputs and three 16-bit timer/counter channels, all at 5 V/TTL levels. This ordering code is supplied with a DN-37 Terminal Board and a CA-3710 D-Sub cable, rather than the CA-4002 D-Sub connector listed for the ISO-DA8 CR.ApplicationsProgrammable voltage sourceProgrammable current sinkHarsh environment operationProcess control
The ISO-DA16 CR is a 16-channel, 14-bit analogue output board for PC/AT compatible computers with an ISA bus. Each output has its own converter and optical isolation rated for up to 2500 Vrms common-mode voltage, which suits programmable voltage sources and programmable current sinks in process control and harsh environments.Output type (unipolar or bipolar) and range can be set in software across 0 ~ 5 V, ±5 V, 0 ~ 10 V and ±10 V. Each converter also provides a 4 ~ 20 mA current sink to ground, and the outputs use double-buffered D/A latches with command set programming.The board is jumperless and trimless. Calibration is carried out under software control with the data held in EEPROM, and the power-on value of each output can be pre-defined and stored on board. This ordering code includes one CA-4002 D-Sub connector.ApplicationsProgrammable voltage sourceProgrammable current sinkHarsh environment operationProcess control
The A-626 CR is an ISA bus data acquisition board for PC-based control systems that need six 12-bit analogue outputs alongside 16 digital inputs and 16 digital outputs. Each D/A channel can be set to a voltage range of 0 ~ 5 V, 0 ~ 10 V, ±5 V or ±10 V, or to a 4 ~ 20 mA sink current output.Why choose this model: It suits engineers building analogue control and test rigs on legacy ISA-based PCs. The on-board BB Ref-01 reference chip is included to reduce thermal drift of the reference voltage. The board connects directly to DB-16P, DB-16R, DB-24PR, DN-20 and DN-37 wiring accessories, and this ordering code includes one CA-4002 D-Sub connector.Driver support covers Linux, DOS, Windows 98/NT/2000 and 32-bit Windows XP/Vista/7, with a DLL and ActiveX control plus sample programs for several development environments, including LabVIEW and Visual Basic. The A-726 is designed to be fully compatible with the A-626.ApplicationsSignal analysisIndustrial automationLaboratory automationSensor interfaceFFT and frequency analysisTransient analysisProduction testProcess control