Others
2AB125R is a DIP resistor of 125 ohm with a tight 0.1% tolerance and a 1/4 W power rating. Its metal film construction gives a temperature coefficient of 50 ppm/℃, which suits circuits where a stable, well-defined resistance value matters.Engineers typically choose this part when a precise fixed value is needed on a DIP-format board, and the RoHS certification is relevant where compliant components are specified.Resistance: 125 ohmTolerance: 0.1%Power rating: 1/4 WTemperature coefficient: 50 ppm/℃
IP67 RJ45 Plug.
Cap with Tether.
IP67 Power Plug (5-pin).
IP67 Power Plug (3-pin).
AFAN-02 CR is a 1U two-way cooling fan module that keeps equipment within its temperature limits by providing active air movement. It accepts two fan modules, so a failed unit can be replaced while the system keeps running.Each fan has its own fault LED, and the relay alarm output signals a fan failure or loss of power. A failure in one fan does not affect the other, and a 5A fuse with overvoltage protection guards the 24 VDC supply.Relay alarm output reports fan failure or power loss to a remote monitoring systemMounted on a wall, the unit is suited to small server cabinetsApplicationsCooling for small server cabinets
The AFAN-04 CR is a 1U cooling fan module for rack-mounted computer room and industrial equipment. It houses four fans that provide active airflow, helping to lower the operating temperature of the equipment and maintain stable operation.Each fan has its own fault LED, and a relay alarm output signals any fan failure or loss of power to a remote monitoring system. Because a single fan failure does not affect the others, the module keeps cooling while a faulty unit is identified and replaced. The fans are hot-swappable, so maintenance can be carried out without shutting down the equipment.The module runs from 24 VDC with a 5A fuse for overvoltage protection and is sized for 19-inch racks. It is suited to engineers specifying thermal management for server rooms and control cabinets, where fan faults must be detected early to avoid overheating.ApplicationsCooling of computer room and server room equipmentThermal management of industrial equipment in 19-inch cabinetsFan fault monitoring with remote alarm signalling
ASO-0015 is an optional wall mount kit for metal-case modules with a 28 mm case width. It lets you fix the module to a wall or panel without a DIN-rail, which suits installations where rail space is limited or the mounting surface is flat.The kit contains two wall mount brackets and six screws, so everything needed for the fixing is supplied in one package. Dimensions for the bracket are given by the manufacturer in millimetres.The kit is RoHS and WEEE certified. Check the case width of your module before ordering, as this accessory is designed only for the 28 mm size.ApplicationsWall mounting of 28 mm wide metal-case modules in control cabinets and panelsInstallations where DIN-rail mounting is not practical
The ASO-0023 is an optional wall mount kit for modules with a 44 mm wide metal case. It lets you fix a compatible module to a wall or panel without a DIN-rail, which suits installations where rail mounting is not practical.The kit contains two wall mounts and six screws, so everything needed for the fixing is included. It is an accessory and must be ordered separately from the module it is intended for.The product is listed as RoHS and WEEE compliant. Check the case width of your module against the 44 mm specification before ordering.ApplicationsWall or panel mounting of 44 mm wide metal-case modules
The ASO-0029 is a universal joint bracket designed as a mounting accessory for the WLS-R01. It is supplied as a dedicated accessory for that unit, so engineers can fix the WLS-R01 with a joint-style bracket rather than a standard fixed mount.The product is listed with RoHS and WEEE certifications. The source page also lists the iSN-301H/DIN and iSN-301V/DIN alongside the WLS-R01, but it does not state fitting details for those models, so confirm compatibility against your own requirements before specifying the bracket with them.Dimensions are referenced on the manufacturer page, but no measurements were supplied with the source data, so check the drawings before planning panel or enclosure layout.ApplicationsMounting the WLS-R01 in industrial installations
The ASO-0054 is a universal joint bracket accessory for the iSN-81x-MRTU Series. It gives system builders a dedicated mounting option when installing these units within a cabinet or machine assembly.Ordered as ASO-0054 CR, this bracket is listed as RoHS compliant and carries WEEE listing, which helps with materials compliance and electronic waste obligations on European projects.Dedicated to the iSN-81x-MRTU SeriesUniversal joint bracket form for flexible mountingApplicationsMounting iSN-81x-MRTU Series units with a universal joint bracket
The ASO-0057 is a wall mount kit for mounting metal case USB-4018HS Series modules on a wall. It is designed to hold two metal case modules with a case length of 153 mm, so two units can be fixed together as a single installation.The kit includes two wall mounts and eight screws. It is listed as RoHS and WEEE compliant, and is intended for engineers who need a simple mechanical fixing for USB-4018HS data acquisition hardware in a cabinet or equipment wall.Choose the ASO-0057 when you need an accessory matched to the 153 mm metal case size rather than a generic bracket. Check the case length of your modules before ordering, as the kit is specified for this case size only.ApplicationsWall mounting of two USB-4018HS metal case modules
ASO-0058 is a wall mount kit for installing a 100 mm wide metal case module on a wall. It is an optional accessory, so it suits installations where a surface mount is preferred to a standard mounting method.The kit contains two wall mounts and four screws, so everything needed for the fixing is included in the box. Dimensions are given in millimetres in the manufacturer's drawing, which should be checked against the module before fitting.Designed for 100 mm case width metal modulesIncludes two wall mounts and four screwsRoHS and WEEE compliantApplicationsWall mounting of 100 mm wide metal case modules in control cabinets, panels or equipment racks
ASO-0059 is an optional wall mount kit for the USB-4018HS Series. It is designed for modules in a metal case with a width of 153 mm, giving a simple way to fix the unit to a wall rather than mounting it on a panel or rail.The kit is supplied with everything needed for the fixing:One wall mount bracketFour screwsThe ASO-0059 is RoHS and WEEE certified. Check the case width of your module against the 153 mm specification before ordering.ApplicationsWall mounting of a 153 mm wide metal-case USB-4018HS module
ASO-0060 is a magnetic base universal joint bracket for holding equipment on ferrous surfaces while allowing the mounting angle to be adjusted. Its NdFeB magnet and iron components provide the holding base, and the TPE rubber parts complete the assembly.The magnet grade is rated N35 ~ N52, and the bracket is specified for an operating temperature range of -40 ~ +80 °C. It is supplied in rubber-sealed packaging and is listed as RoHS and WEEE compliant.Suitable for positioning and mounting on steel or other ferrous surfacesMagnet grade N35 ~ N52Operating temperature -40 ~ +80 °CApplicationsMounting and positioning on steel or other ferrous surfaces
ASO-0062 is a DIN-rail mount clip with a 28 mm width, supplied with one clip and two screws. It gives engineers a simple way to fix compatible ICP DAS equipment to a standard DIN rail inside a control cabinet.The clip is sold as the ordering code ASO-0062 and carries RoHS and WEEE certification. The source data lists the ordering entry as ASO-0062 CR with the same description, so the 28 mm width and the included parts apply to that listing.28 mm clip widthSupplied with one DIN-rail clip and two screwsRoHS and WEEE certified
The ASO-0063 is a DIN-rail mount clip accessory with a 44 mm width, intended for fitting equipment to a DIN rail. It is supplied as a kit with one DIN-rail clip and four screws, so the mounting hardware is ready to use on installation.Choose this accessory when you need a simple, standard DIN-rail mounting solution. The source data lists it as RoHS and WEEE certified, and the dimensions are given in millimetres.Width of 44 mmKit includes one DIN-rail clip and four screwsListed as RoHS and WEEE certifiedDimensions specified in millimetresApplicationsDIN-rail mounting
ASO-0064 is a 60 mm wide DIN-rail mount clip for mounting compatible equipment on a DIN rail. It is supplied with one DIN-rail clip and four screws.The source lists the clip with RoHS and WEEE certifications. Dimensions are provided in millimetres in the manufacturer's documentation.Choose this accessory when you need a 60 mm width DIN-rail clip with the included fixings for panel or cabinet installation.
One Additional THIN CLIENT.
The BX-ENEL5-1 CR is a battery box that holds a Nikon ENEL5 battery. It is designed to be fitted on a DIN rail, so it can be installed in a control cabinet or equipment rack alongside other automation hardware. The user must insert the Nikon ENEL5 battery before use.A 15 cm cable is included for connecting the battery box to the equipment it serves. The compact housing measures 56mm (width) x 75mm (length) x 16mm (height), which keeps the footprint small on a crowded DIN rail.The BX-ENEL5-1 CR is certified to RoHS and WEEE. Check the dimensions and cable length against your installation before ordering.
USB 2.0 A-Male to Mini-5P B-Male Cable, 1M.
CD-002 is a split ferrite core for suppressing electromagnetic and radio-frequency interference on round cables. Its hinged plastic case closes around the cable and holds the ferrite securely in place, so it can be fitted without re-terminating the cable.The core is aimed at low-frequency noise generated by engine control units, inverters and motors. It can be retrofitted to installed equipment or added during post-assembly work on the data and power cables of electronic devices, which suits environments where EMI or RFI affects signal integrity.Each package contains 10 cores, supplied in white and rated for an operating temperature of -40 °C to 75 °C. Maximum cable diameter is Ø13 mm.ApplicationsSuppressing low-frequency noise from engine control unitsReducing noise from inverters and motorsReducing EMI and RFI on data cables of electronic equipmentReducing EMI and RFI on power cables of electronic equipmentRetrofitting existing installations
DRS-125 is a 125mm length of 35mm DIN-rail made from stainless SUS304 at 1.0t thickness. It provides a corrosion-resistant mounting track for equipment in panels and enclosures where a standard DIN-rail is required.The rail is prepunched with 10mm feed-through holes along its length, which allow it to be fixed in place with the holes provided. Dimensions are given in millimetres on the manufacturer's drawing.