DN-20/N Two 20-pin Header to Screw Terminal Board, 5.08 mm Pitch

The DN-20-381 is a DAQ daughter board that breaks out two 20-pin headers to pin-to-pin screw terminals, giving engineers a practical way to wire I/O signals from a 20-pin header to field connections. It is designed for DIN-rail mounting in a cabinet and has a 3.81 mm terminal pitch.Two CA-2010 flat cables (20-pin, 1 m) are included, so the board can be connected to a compatible header source straight out of the box. The board measures 103 mm x 86 mm and is rated for an operating temperature of 0 ~ 60°C.The DN-20-381 carries CE, UKCA, FCC and WEEE marks. Check the header layout of your host board before ordering, as the terminal board is intended for 20-pin header I/O.ApplicationsWiring field signals from 20-pin header DAQ daughter board I/O to screw terminalsCabinet installations using DIN-rail mounted terminal wiring

DN-20 CR is a DIN-rail mounted I/O connector block that breaks out two 20-pin headers to pin-to-pin screw terminals, giving engineers a practical way to wire field signals in a control cabinet instead of terminating flat cables directly.Each 20-pin header is routed to its own set of screw terminals at a 5.08 mm pitch, so the wiring can be checked and serviced without disturbing the cable connections. The board is supplied with two CA-2010 flat cables, each 20-pin and 1 m long, for connection to the header side.The board is rated for 0 ~ 60°C operation and carries CE, UKCA, FCC, RoHS and WEEE certification marks. Overall dimensions are 147 mm x 75 mm.ApplicationsField wiring for 20-pin header I/O connectionsControl cabinet installation on DIN-rail

DN-20M CR is a motion control daughter board for ICP DAS 6-axis controllers including the PISO-PS600, PISO-VS600, I-8196F, I-9196F and PMDK. It gives engineers a practical way to wire a full-function manual pulse generator (MPG) to the controller without custom cabling, while also providing a point for FRnet connection.Signals are routed through screw terminals for straightforward field wiring, with a pin-to-pin screw terminal arrangement for the connected manual pulse generator. On-board isolating circuitry is included to help protect the controller, and a 20-pin SCSI-II connector and RJ-45 port complete the interface options. The board mounts on a DIN rail.Suited to panel layouts where the manual pulse generator and FRnet wiring need to be terminated neatlyOperating range of -20 ~ +75 °C and 10 ~ 90% RH, non-condensingApplicationsManual pulse generator input for motion control systemsFRnet connection on ICP DAS 6-axis motion controllersMotion control wiring for PISO-PS600, PISO-VS600, I-8196F, I-9196F and PMDK controllers

The DN-25 CR is a DIN-rail I/O connector block that breaks out signals from 9-pin and 25-pin D-sub connectors to screw terminals, giving engineers an accessible wiring point for field connections. It is listed in the DAQ daughter board accessories category.Each pin of the D-sub connectors is wired pin-to-pin to a screw terminal with 5.08 mm pitch, which keeps field wiring straightforward. The block measures 48 mm x 76 mm and mounts on a DIN rail.The package includes two cables: a CA-0920 DB9 (male) to DB9 (male) cable wired RS-232 Pin1-Pin9, 2M long, and a CA-2520 DB25 male to male cable, 45º, 2M long. The unit is rated for 0 ~ 60°C operation and -20 ~ 70°C storage, with 5% ~ 90% RH non-condensing humidity, and carries CE, UKCA, FCC, RoHS and WEEE certifications.ApplicationsWiring field I/O signals to D-sub connected data acquisition hardwareDIN-rail installation in control cabinets