MN-SERVO-DAA Motionnet Single-axis Motion Control Module for Delta ASDA-A/A2
Single-axis Motionnet distributed motion control module for Delta ASDA-A/A2 servo drivers, with spring-type terminal blocks and up to 20 Mbps communication.
- Motionnet communication at 2.5, 5, 10 or 20 Mbps
- Pulse output up to 6.6 MHz in OUT/DIR or CW/CCW mode
- Up to 64 single-axis modules on one serial line
- Multi-axis linear and 2-axis circular interpolation
- T/S-curve acceleration and deceleration, with speed and position changes on the fly
- Home, slow-down and positive/negative limit sensor inputs for each axis
281,00 € per piece
| 1–9 pcs | 281,00 € | |
|---|---|---|
| 10–30 pcs | 273,00 € | −3 % |
| 31+ pcs | 267,00 € | −5 % |
Informácie o výrobku "MN-SERVO-DAA Motionnet Single-axis Motion Control Module for Delta ASDA-A/A2"
The MN-SERVO-DAA is a single-axis motion control module that plugs directly into a Delta ASDA-A/A2 servo drive and joins a Motionnet line through a standard Cat.5 LAN cable. It adds an axis to a distributed motion system without a separate controller-side wiring run to each drive, which suits compact, highly integrated machine automation.
Each module handles pulse output of up to 6.6 MHz, encoder input and the limit, home and slow-down sensor inputs for its axis. Up to 64 axes can be controlled on one line, with multi-axis linear and 2-axis circular interpolation, and T/S-curve acceleration and deceleration. Speed and position can be changed on the fly.
The CR ordering version is fitted with spring-type terminal blocks as standard, so no additional terminal board is needed. Three-way isolation between power, communication and I/O is provided for better noise immunity and device protection.
Applications
- Distributed multi-axis motion control in machine automation
- Axis expansion for Delta ASDA-A/A2 servo drive systems
| Product type: | Motion control module |
|---|---|
| Interface: | Motionnet |
| Protocol: | Motionnet |
| Isolation: | Three-way (power, communication, I/O) |
| Power input: | 24VDC +/-5% |
| Operating temperature: | 0 ~ +60 °C |
Specifications
| LED Indicators | |
|---|---|
| Status | Communication state (Link, Error) Internal 3.3 V Power Termination Resistor Switch Mechanic Switch Input |
| General | |
| Speed Profile | Trapezoidal/S Shaped Acc/Dec Driving |
| Auto-Home Search | 13 Types |
| Axis I/O | |
| Servo Interface Output | SVON, ERC, ALM_RST |
| Latch Input | Yes (shared with SD) |
| Mechanical Switch Input | LMT+, LMT-, HOME, SD, EMG |
| Position Compare Output | High-Speed 5 V TTL or 24 V open collector |
| Servo Interface Input | ALM, RDY, INP |
| Encoder Input | |
| Mode | CW/CCW, A/B phase |
| Counter Width | 28-bit |
| Pulse Output | |
| Mode | OUT/DIR, CW/CCW |
| Counter Width | 28-bit |
| Rate | 6.6 MHz (Max.) |
| Motionnet | |
| Communication Connectors | Spring Type Terminal Blocks |
| Transfer Speed | 2.5, 5, 10, 20 Mbps |
| Power | |
| Input Range | 24VDC +/-5% (1000 V isolated) |
| Environment | |
| Operating Temperature | 0 ~ +60 °C |
| Storage Temperature | -20 ~ +80°C |
| Humidity | 10 ~ 90% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Prihlásiť sa