GW-7552-B PROFIBUS DP-V0 to Modbus RTU/ASCII Gateway, Plastic Case
PROFIBUS DP-V0 slave gateway that lets a PROFIBUS master reach Modbus RTU/ASCII devices through a hybrid RS-232/422/485 COM port, mounted on a DIN rail.
- DP-V0 slave on PROFIBUS with automatic transmission rate detection across 9.6 kbps to 12 Mbps
- Modbus master or slave mode with RTU and ASCII format support
- Hybrid COM 1 port selectable as RS-232, RS-422 or RS-485
- Up to 132 bytes input and 131 bytes output data length
- Node address 0 to 126 set by DIP switch
- 3000 VDC DC isolation on the PROFIBUS side and High Speed iCoupler network isolation
371,00 € per piece
| 1–9 pcs | 371,00 € | |
|---|---|---|
| 10–30 pcs | 360,00 € | −3 % |
| 31+ pcs | 353,00 € | −5 % |
Informácie o výrobku "GW-7552-B PROFIBUS DP-V0 to Modbus RTU/ASCII Gateway, Plastic Case"
The GW-7552-B connects Modbus devices to a PROFIBUS DP network. It acts as a DP-V0 slave towards the PROFIBUS master, so the master can read and write data held by Modbus devices such as PLCs, sensors and ICP DAS M-7000 series modules, without changes to the PROFIBUS network design.
The gateway can operate as a Modbus master or slave and supports both RTU and ASCII formats. Its hybrid COM 1 port is selectable between RS-232, RS-422 and RS-485, with the modes used one at a time. Serial settings cover 7 or 8 data bits, no, odd or even parity, 1 or 2 stop bits, and baud rates from 1200 to 115200. A utility is provided for configuring the GW-7552-B.
Transmission rate on the PROFIBUS side is detected automatically, and the node address is set from 0 to 126 using a DIP switch. The PROFIBUS side has 3000 VDC isolation, and the network side uses High Speed iCoupler isolation. The GW-7552-B is housed in a plastic case for DIN-rail mounting, with an operating range of -25 ~ +75 °C.
Applications
- Industrial automation
- Factory automation
- Process automation
| Product type: | Gateway |
|---|---|
| Interface: | RS-232/422/485 |
| Protocol: | PROFIBUS DP-V0 / Modbus RTU/ASCII |
| Isolation: | 3000 VDC |
| Operating temperature: | -25 ~ +75 °C |
| Mounting: | DIN-rail |
| Housing: | Plastic |
Specifications
| CPU Module | |
|---|---|
| CPU | 80186, 80 MHz or compatible |
| EEPROM | 16 KB |
| Flash | 512 KB |
| SRAM | 512 KB |
| Watchdog Timer | Watchdog IC CPU built-in |
| LED Indicators | |
| Status | PWR LED, RUN LED, ERR LED |
| COM Ports | |
| Ports | RS-232/RS-422/RS-485(can’t be used simultaneously) 3-pin screwed terminal block (RxD, TxD, GND) 4-pin screwed terminal block (RxD+, RxD-, TxD+, TxD-) 2-pin screwed terminal block (DATA+, DATA-) |
| Baud Rate | 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 |
| Parity | None, Even, Odd |
| Data Bit | 7, 8 |
| Stop Bit | 1, 2 |
| PROFIBUS | |
| Controller | Siemens SPC3 |
| Transceiver | ADI ADM2486 |
| Baud Rate | 9.6 k, 19.2 k, 45.45 k, 93.75 k, 187.5 k, 500 k, 1.5 M, 3 M, 6 M, 12 M |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for bus-to-logic |
| Protocol | DP-V0 |
| Power | |
| Consumption | 2.5 W |
| Mechanical | |
| Dimensions (mm) | 72 x 33 x 119 (W x L x H) |
| Installation | DIN-Rail |
| Environment | |
| Operating Temperature | -25 ~ +75℃ |
| Storage Temperature | -30 ~ +85 ℃ |
| Humidity | 5 ~ 95% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Prihlásiť sa