PEX-CPM100-T PCI Express CANopen Master Board, 1 Port, 5-Pin Screw Terminal
1-port intelligent CANopen master PCI Express board with NXP SJA1000T controller, CiA 301 v4.02 support and up to 127 slaves for PC-based CANopen control.
- Active CANopen master on one CAN channel, conforming to CiA 301 v4.02
- Manages up to 127 slaves, with a scan function and master listen mode
- Node Guarding and Heartbeat Consumer protocols with event triggering for EMCY, Node Guarding and Heartbeat
- Flexible PDO handling: event-triggered, remote-requested, cyclic and acyclic SYNC, plus dynamic mapping
- NXP SJA1000T CAN controller with 82C250 transceiver, 10 k ~ 1 M baud and built-in 120Ω terminal resistor
- Isolation of 3000 VDC (DC-to-DC) and 2500 Vrms (photo-coupler)
460,00 € per piece
| 1–9 pcs | 460,00 € | |
|---|---|---|
| 10–30 pcs | 446,00 € | −3 % |
| 31+ pcs | 437,00 € | −5 % |
Info sui prodotti "PEX-CPM100-T PCI Express CANopen Master Board, 1 Port, 5-Pin Screw Terminal"
The PEX-CPM100-T CR is a PCI Express card that turns a host PC into an active CANopen master on a single CAN channel. A 16-bit on-board microcontroller runs the CANopen firmware, so time-critical network handling stays on the card, even when the PCI bus is heavily loaded.
Your application exchanges data with the firmware through memory mapping, and you can also build CANopen applications on the host using the supplied CANopen library. The CANopen Motion Library, which follows CiA 402, adds position, velocity, torque and synchronised control.
Network management features include a scan function for all nodes, master listen mode, Node Guarding and Heartbeat Consumer protocols, and automatic node addition at boot. Driver and SDK support is provided for Windows XP, 7, 8 and 10 in both 32-bit and 64-bit versions.
Applications
- PC-based CANopen master control on industrial fieldbus networks
- CANopen motion control using the CANopen Motion Library (CiA 402)
| Product type: | PCI Express board |
|---|---|
| Interface: | PCI Express |
| Protocol: | CANopen |
| Ports: | 1 |
| Isolation: | 3000 VDC (DC-to-DC), 2500 Vrms (photo-coupler) |
| Power input: | 300 mA @ 5 |
| Operating temperature: | 0 ~ +60 °C |
Specifications
| Software | |
|---|---|
| Driver | Windows XP/7/8/10 (32-bit/64-bit OS) |
| SDK | VB 6.0, BCB 6.0, VC++, C#.net, VB.net |
| CPU Module | |
| CPU | 80186, 80 MHz or compatible |
| EEPROM | 16 KB |
| Flash | 512 KB |
| SRAM | 512 KB |
| Watchdog Timer | Hardware watchdog |
| LED Indicators | |
| Status | 1 x Power and Communication |
| PC Bus | |
| Type | PCI Express bus |
| Board No. | By DIP switch |
| CANopen | |
| Controller | NXP SJA1000T with 16 MHz clock |
| Ports | 1 |
| Baud Rate | 10 k ~ 1 M |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple |
| Terminal Resistor | Built-in 120Ω |
| Protocol | CiA 301 v4.02 |
| NMT | Master |
| Power | |
| Consumption | 300 mA @ 5 |
| Mechanical | |
| Dimensions (mm) | 133 x 22 x 98 (W x L x H) |
| Environment | |
| Operating Temperature | 0 ~ +60 °C |
| Storage Temperature | -20 ~ +70 °C |
| Humidity | 5 ~ 85% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Login