R-9028CH Redundant 8-ch 4~20mA Current Output Module, HART Master
Redundant 8-channel, 16-bit isolated 4~20mA current output module with built-in HART master for RIO-98x0 systems. Ordering code R-9028CH CR (RoHS).
- 8 isolated 4~20mA current output channels, 16-bit D/A resolution
- Accuracy ±0.05% FSR with ±25% overrange (0 ~ 24 mA)
- Built-in HART master for point-to-point device access
- Power-on value and safe value for defined output states
- Channel and terminal board disconnection detection
- Redundant switching time below 1 ms within the RIO-98x0 system
1.568,00 € per piece
| 1–9 pcs | 1.568,00 € | |
|---|---|---|
| 10–30 pcs | 1.521,00 € | −3 % |
| 31+ pcs | 1.489,00 € | −5 % |
Informacije o izdelku "R-9028CH Redundant 8-ch 4~20mA Current Output Module, HART Master"
R-9028CH CR is an 8-channel analogue current output module for the RIO-98x0 redundant I/O system. Each channel is a 16-bit, channel-isolated 4~20mA source output with a tolerance of ±0.05% FSR, and it can drive up to ±25% overrange (0 ~ 24 mA).
The module suits applications where reliable actuator or field device control and wiring supervision matter. Power-on and safe values define the output state during start-up or abnormal conditions, while channel and terminal board disconnection detection help confirm wiring integrity. A built-in HART master lets engineers read HART device information from connected point-to-point instruments.
Redundancy is supported, so the system can keep operating if a single I/O module fails, with a switching time below 1 ms. The module requires an RDB-S09 or RDB-D09 terminal board for external connections and provides 3000 VDC isolation between the power supply and the backplane bus.
Applications
- Building Automation
- Factory Automation
- Machine Automation
- Remote Maintenance
- Remote Diagnosis
- Testing Equipment
| Product type: | Analog output module |
|---|---|
| Protocol: | HART |
| Analog outputs: | 8 |
| Isolation: | 3000 VDC |
| Operating temperature: | -25 ~ +70 °C |
Specifications
| EMS Protection | |
|---|---|
| EFT (IEC 61000-4-4) | Yes |
| ESD (IEC 61000-4-2) | Yes |
| LED Indicators | |
| Status | 1 PWR, 1 MOD, 1 ACT, 1 DX, 1 ERR LED 0~7 for CH High/Low Alarm LED 16~23 for CH Break Line |
| Analog Output | |
| Channels | 8 |
| Type | 4~20 mA (Support ±25% overrange) |
| Range | ±25% (0 ~ 24 mA) |
| Resolution | 16 bit |
| Accuracy | ±0.05% FSR |
| Zero Drift | ±1.5 ppm/℃ |
| Span Drift | ±3 ppm/℃ |
| Response Time | <200 μS |
| Open Wire Detection | Yes |
| Current Load Resistance | < 1K Ω |
| Power-on Value | Yes |
| Safe Value | Yes |
| Isolation | 3000 VDC |
| I/O Expansion | |
| I/O Type | RDB-S09 / RDB-D09 |
| HART | |
| Topology | Master, Monodrop (Point-to-Point) |
| Power | |
| Consumption | 5.6 W |
| Mechanical | |
| Dimensions (mm) | 33 x 129 x 130 |
| Environment | |
| Operating Temperature | -25 °C ~ +70 °C |
| Humidity | 5 ~ 95% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Prijava