CAN-2088C CANopen Slave I/O Module, 8-ch PWM Output, 8-ch Counter Input
CANopen slave module with 8 hardware-controlled PWM outputs and 8 high speed counter inputs for building cost-effective analogue-style control systems.
- Hardware-controlled PWM outputs from 0.2 Hz to 500 kHz with 0.1 ~ 99.9 % duty cycle
- Software or hardware trigger, with individual or synchronous triggering of all PWM outputs
- Burst and Continuous output modes
- 32-bit 500 kHz high speed counter on each of the 8 digital input channels
- CiA 301 v4.02 and CiA 401 v2.1 support, passed CANopen conformance test
- EDS file provided for CANopen master configuration
237,00 € per piece
| 1–9 pcs | 237,00 € | |
|---|---|---|
| 10–30 pcs | 230,00 € | −3 % |
| 31+ pcs | 225,00 € | −5 % |
Informacije o izdelku "CAN-2088C CANopen Slave I/O Module, 8-ch PWM Output, 8-ch Counter Input"
CAN-2088C CR is a CANopen slave module that turns digital outputs into PWM signals with adjustable frequency and duty cycle. Its eight PWM channels can drive analogue control circuits from a fieldbus master, so engineers can achieve proportional-style control without dedicated analogue output hardware.
Each of the eight digital input channels carries a 32-bit counter running at up to 500 kHz, allowing high speed pulse counting alongside the PWM outputs in the same node. PWM can be triggered by software or hardware, and each output can be started individually or all outputs can be triggered synchronously. Burst and Continuous output modes are supported.
The module follows CiA 301 v4.02 and CiA 401 v2.1, has passed the CANopen conformance test and is supplied with an EDS file for configuring the CANopen master. It mounts on DIN-rail and operates from -25 ~ +75 °C.
Applications
- Analogue-style control circuits driven by PWM outputs
- CANopen networks requiring combined PWM output and high speed counting
| Product type: | CANopen slave module |
|---|---|
| Interface: | CANopen |
| Protocol: | CANopen |
| Digital inputs: | 8 |
| Isolation: | 3000 VDC / 2500 Vrms |
| Operating temperature: | -25 ~ +75 °C |
| Mounting: | DIN-rail |
Specifications
| CPU Module | |
|---|---|
| Watchdog Timer | Hardware watchdog |
| LED Indicators | |
| Status | 3 LEDs to PWR, RUN and ERR |
| Digital Input | |
| Channels | 8 |
| Type | Wet Contact |
| Sink/Source (NPN/PNP) | Sink |
| ON Voltage Level | +5.5 ~ +30 VDC |
| OFF Voltage Level | <3.5 VDC |
| Input Impedance | 2.2 kΩ, 0.5 W |
| PWM | |
| Channels | 8 |
| Sink/Source (NPN/PNP) | Source |
| Load Current | 1 mA |
| Frequency | 0.2 Hz ~ 500 kHz (non-continuous) |
| Duty Cycle | 0.1 ~ 99.9 % |
| Mode | Burst mode, Continuous mode |
| Trigger Start | Hardware (Start and Stop) or Software (Start and Stop) |
| CANopen | |
| Baud Rate | 10 k ~ 1 M |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple |
| Terminal Resistor | Built-in 120Ω |
| Protocol | CiA 301 v4.02, CiA 401 v2.1 |
| Node ID | 1 ~ 99 |
| No. of PDOs | 10 RxPDO , 10 TxPDO |
| PDO Mode | Event Triggered, Remotely requested, Cyclic and acyclic SYNC |
| Error Control | Node Guarding protocol / Heartbeat Producer |
| NMT | Slave |
| EMCY Message | Yes |
| Power | |
| Consumption | 3.5 W |
| Mechanical | |
| Dimensions (mm) | 33 x 99 x 78 ( W x L x H ) |
| Installation | DIN-Rail |
| Environment | |
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -30 ~ +80 °C |
| Humidity | 10 ~ 90% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Prijava