XW107 XW-board Expansion, 8-ch Dry DI and 8-ch Sink DO

XW107i CR is an XW-board expansion module that adds 8 isolated digital inputs and 8 isolated digital outputs to a compatible PAC. It is intended for the uPAC-5000, LP-51xx and WP-51xx series, and each PAC accepts only one XW-board.The digital inputs are wet-contact type, with ON levels from +10 VDC to +50 VDC and an OFF level of +4 VDC maximum. Sink or source operation is selected by jumper, and each input channel is isolated to 3750 VDC with 60 VDC overvoltage protection. The outputs are open-collector, sink-type (NPN) channels rated for 10 to 40 VDC loads at 200 mA per channel at 25 °C, with 3750 VDC isolation and 1.4 A overload protection.The board draws 0.4 W and measures 66 mm x 82 mm x 17 mm (W x L x H). It operates from -25 to +75 °C and stores from -30 to +75 °C, at 10 to 95% RH non-condensing. Certifications listed for this ordering code are CE, UKCA, FCC, RoHS and WEEE.ApplicationsAdding digital I/O to uPAC-5000, LP-51xx and WP-51xx controllersReading wet-contact switch and sensor signals from 10 to 50 VDC circuitsSwitching 10 to 40 VDC sink-type loads from a PAC

The XW110i CR is a 16-channel isolated digital input expansion board from the XW-board series, designed for the uPAC-5000, LP-51xx and WP-51xx PAC platforms. It adds 16 digital inputs that accept either dry contact or wet contact signals, so a single board can handle switches and relays as well as DC voltage signals.Each channel supports sink or source type wiring. The wet contact input turns ON at +10 VDC to +50 VDC and OFF at +4 VDC maximum, while the dry contact input turns ON when closed to GND and OFF when open. Isolation is rated at 3750 VDC and the wet contact inputs are protected against overvoltage up to 60 VDC.Only one XW-board can be fitted to each PAC, so the XW110i CR is suited to projects where the controller's onboard I/O needs a 16-point isolated digital input extension. Typical power consumption is 0.6 W, and the board operates from -25 to +75 °C.ApplicationsDigital input expansion for uPAC-5000 PAC systemsDigital input expansion for LP-51xx PAC systemsDigital input expansion for WP-51xx PAC systemsMonitoring of dry contact switches and wet contact DC signals

The XW111i CR adds 16 isolated digital outputs to a compatible PAC. It is an XW-board for the uPAC-5000, LP-51xx and WP-51xx series, so the controller's I/O can be extended without a separate remote module.Output design: each channel is an open-collector, sink-type (NPN) output. Loads from +10 VDC to +50 VDC can be switched, with up to 350 mA per channel at 25 °C and 1.4 A overload protection, and the outputs are isolated to 3750 VDC.Installation note: one PAC accepts only one XW-board, so plan the I/O count of each controller accordingly. The unit draws 0.2 W and is rated for an operating range of -25 ~ +75 °C.ApplicationsSwitching DC loads from a uPAC-5000, LP-51xx or WP-51xx controllerAdding isolated digital outputs to an existing PAC I/O configuration

The XW304 CR is an XW-board that adds analogue and digital I/O to the uPAC-5000, LP-51xx and WP-51xx series controllers. It combines six voltage inputs, one voltage output, four dry-contact digital inputs and four open-collector digital outputs on one board, which suits controllers that need a few extra signals.Each host controller accepts one XW-board. The analogue inputs support ±5 V and 0 ~ +5 V ranges with 12-bit resolution and a 4 kHz sampling rate. The single analogue output covers ±5 V and is rated for 20 mA.The digital outputs are NPN sink type with a 10 ~ 40 VDC load voltage, rated at 200 mA per channel at 25 °C and protected against overload up to 1.4 A. The board operates from -25 ~ +75 °C and carries CE, UKCA, FCC, RoHS and WEEE marks.ApplicationsAdding analogue and digital I/O to uPAC-5000, LP-51xx and WP-51xx controllers