PCI-1602U Universal PCI DAQ Board, 100 kS/s 16-bit AI Multifunction Card
Universal PCI multifunction board with 32 single-ended or 16 differential 16-bit analogue inputs at up to 100 kS/s, plus 2 analogue outputs and 16 digital inputs and 16 digital outputs.
- Universal PCI interface compatible with both 3.3 V and 5 V PCI bus
- 32 single-ended or 16 differential 16-bit analogue inputs, jumper selectable
- 100 kS/s AD converter with 8 K-sample hardware FIFO and MagicScan multi-channel scanning
- Programmable gain of 1, 2, 4 and 8 with bipolar ranges from ±1.25 V to ±10 V
- 2-channel 12-bit analogue output with ±5 V and ±10 V ranges
- 16-channel 5 V/TTL digital input with pull-high and pull-low resistors, plus 16-channel digital output
988,00 € per piece
| 1-9 pcs | 988,00 € | |
|---|---|---|
| 10-30 pcs | 938,00 € | −5 % |
| 31+ pcs | 889,00 € | −10 % |
Produkta informācija "PCI-1602U Universal PCI DAQ Board, 100 kS/s 16-bit AI Multifunction Card"
The PCI-1602U CR is a high-performance multifunction card for high-speed analogue and digital I/O on a PC. It uses the Universal PCI interface, so it runs on either a 3.3 V or a 5 V PCI bus. The 16-bit AD converter samples at up to 100 kS/s, buffered by an 8 K-sample hardware FIFO and a MagicScan controller for multi-channel scanning.
The analogue inputs can be configured as 32 single-ended or 16 differential channels using jumpers, with a programmable gain of 1, 2, 4 or 8 and bipolar ranges from ±1.25 V to ±10 V. Two 12-bit analogue outputs and 16 channels each of 5 V/TTL digital input and output complete the I/O set. Pull-high and pull-low resistors on the digital inputs hold a predefined state when channels are disconnected or interrupted.
A Card ID switch lets software identify this board when two or more PCI-1602U cards are installed in the same computer. Software support covers Linux, DOS and Windows, with a DLL, an ActiveX control and sample programs for several development environments. This ordering code includes one CA-4002 D-Sub connector.
Applications
- High speed data acquisition systems
- Process monitoring and control
- Vibration analysis
- Digital pattern generation from the digital I/O port
| Product type: | DAQ board |
|---|---|
| Interface: | Universal PCI |
| Operating temperature: | 0 ~ +60 °C |
Specifications
| Hardware | |
|---|---|
| Connector | Female DB37 x 1 Male 20-bit ribbon x 2 |
| Card ID | Yes (4-bit) |
| Analog Input | |
| Channels | 32 single-ended/16 differential |
| Range | Gain: 1, 2, 4, 8 Bipolar Range: ±10 V, ±5 V, ±2.5 V, ±1.25 V |
| Resolution | 16-bit |
| Accuracy | 0.01 % of FSR ±1 LSB @ 25 °C, ±10 V |
| Sampling Rate | PCI-1602U：100 kS/s. Max. PCI-1602FU：200 kS/s. Max. |
| Input Impedance | 10 MΩ/6 pF |
| Overvoltage Protection | Continuous ±35 Vp-p |
| Zero Drift | ±4 ppm/°C of FSR |
| FIFO Size | 8192 samples |
| Trigger Mode | Software, Internal programmable pacer, External (5 V/TTL) |
| Data Transfer | Polling |
| Analog Output | |
| Channels | 2 |
| Range | Bipolar:±5 V, ±10 V |
| Resolution | 12-bit |
| Accuracy | 0.06% of FSR ±1 LSB @ 25 °C, ±10 V |
| Response Time | 1.0 MHz (Typical) |
| Voltage Output Capability | ±5 mA |
| Slew Rate | 8.33 V/μs |
| Operation Mode | Static Update |
| Digital Input | |
| Channels | 16 |
| Type | 5 V/TTL |
| ON Voltage Level | 2.0 V Min. |
| OFF Voltage Level | 0.8 V Max. |
| Response Speed | 1.0 MHz (Typical) |
| Trigger Mode | Static Update |
| Digital Output | |
| Channels | 16 |
| Type | 5 V/TTL |
| Operation Mode | Static Update |
| Load Voltage | Logic 0: 0.4 V Max. Logic 1: 2.4 V Min. |
| Load Current | Sink: 2.4 mA @ 0.8 V Source: 0.8 mA @ 2.0 V |
| Response Speed | 1.0 MHz (Typical) |
| Timer/Counter/Frequency | |
| Channels | 3 (Independent x 1/Internal pacer x 1/External pacer x 1) |
| Type | 5 V/TTL |
| Resolution | 16-bit |
| Input Frequency | 10 MHz Max. |
| Reference Clock | Internal: 8 MHz |
| PC Bus | |
| Type | 3.3 V/5 V Universal PCI, 32-bit, 33 MHz |
| Data Bus | 16-bit |
| Power | |
| Consumption | 300 mA @ +5 V |
| Mechanical | |
| Dimensions (mm) | 105 x 188 x 22 (W x L x D) |
| Environment | |
| Operating Temperature | 0 ~ +60°C |
| Storage Temperature | -20 ~ +70°C |
| Humidity | 5 ~ 85% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Ienākt
Piederumi
2AB125R is a DIP resistor of 125 ohm with a tight 0.1% tolerance and a 1/4 W power rating. Its metal film construction gives a temperature coefficient of 50 ppm/℃, which suits circuits where a stable, well-defined resistance value matters.Engineers typically choose this part when a precise fixed value is needed on a DIP-format board, and the RoHS certification is relevant where compliant components are specified.Resistance: 125 ohmTolerance: 0.1%Power rating: 1/4 WTemperature coefficient: 50 ppm/℃
ADP-20/PCI CR is a 20-pin to 20-pin connector extender for PCI card wiring. It carries a dual 20-pin flat cable connection over a longer run, so the card can be reached from a more convenient location.The kit includes one CA-2002 flat cable set, 20-pin, 20 cm long, supplied as two cables. This lets you start wiring straight away without sourcing a matching cable separately.The extender is RoHS compliant. It belongs to the DAQ daughter board accessory range, so it suits engineers building or servicing data acquisition setups that use PCI cards.
Flat Cable, 20-pin, 20cm (1 set 2 cables).
Flat Cable, 20-pin, 1M.
Flat Cable, 20-pin, 2M.
DB37 Male to Male Cable, 1M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 1.5M.
DB37 Male to Male Cable, Thin Monolithic Design (High Speed), 3M.
The DB-16P CR is a 16-channel isolated digital input daughter board for the A-82X board, any 812pg, 711, 726 or 720 series board, and PCI-Bus multi-function boards. Each channel uses a bi-directional opto-coupler with a resistor for current sensing, so the board works with both DC and AC inputs.Use it to sense DC signals from TTL levels up to 24 V or a wide range of AC signals. Optical isolation protects the host computer from large common-mode voltages, ground loops and voltage spikes that are common in industrial environments.ON level: 2.8 VDC~24VDC (max), or 4 VAC~24VAC (max) at 1KHzOFF level: 1 VDC (max), or 1 VAC (max) at 1KHzResponse speed: 20us without filter / 2.2ms with filterPower consumption: 12V /0.53A ; 5V / 0.2AApplicationsIsolated digital input sensingEnergy managementTest automationProcess control
The DB-16R is a 16-channel relay output daughter board that lets a digital output port switch 16 Form C relays. Each relay is energised by applying a 5 V signal to its channel on the 20-pin flat cable connector, so the board can be controlled directly from an A-82X, a DIO-64 or any other compatible digital output port.Each relay has an indicator LED that lights while the relay is active, which makes channel status easy to check during commissioning and fault finding. Field wiring is made through screw terminals, and a separate screw-terminal power input is provided so the board does not draw its supply from the host PC.Relay contact rating: 0.5 A at 120 VAC or 1 A at 24 VDCOperate time 6 ms, release time 3 msIncludes CA-2010 flat cable, 20-pin, 1 mApplicationsOn/off controlEnergy managementTest automationProcess control
DB-1825 CR is a female DB37 to screw terminal board that gives engineers a practical way to wire field signals to PCI-1202U, PCI-1602U and PCI-1802U data acquisition cards. Connection is made through a single 37-pin cable, with 32 single-ended channels and 16 differential channels available on the terminals.The ordering code includes a CA-3710 cable (DB37 male to male, 45º, 1 m), so the board can be connected to the DAQ card straight out of the box. The board also provides blank pads for break detection, a low-pass filter, a current shunt and a voltage divider, which are fitted by manual soldering when needed.The board measures 170 mm x 114 mm and is rated for an operating temperature of 0~ +60 °C, a storage temperature of -30 ~ +80 °C and a humidity range of 10% ~ 90%, non-condensing.ApplicationsWiring field signals to PCI-1202U, PCI-1602U and PCI-1802U data acquisition cardsAdding user-fitted signal conditioning such as filtering, current shunting or voltage division on the board
DN-20 CR is a DIN-rail mounted I/O connector block that breaks out two 20-pin headers to pin-to-pin screw terminals, giving engineers a practical way to wire field signals in a control cabinet instead of terminating flat cables directly.Each 20-pin header is routed to its own set of screw terminals at a 5.08 mm pitch, so the wiring can be checked and serviced without disturbing the cable connections. The board is supplied with two CA-2010 flat cables, each 20-pin and 1 m long, for connection to the header side.The board is rated for 0 ~ 60°C operation and carries CE, UKCA, FCC, RoHS and WEEE certification marks. Overall dimensions are 147 mm x 75 mm.ApplicationsField wiring for 20-pin header I/O connectionsControl cabinet installation on DIN-rail
Līdzīgi produkti
The PCI-1602U/S CR is the 100 kS/s version of the PCI-1602U multifunction board. It combines a 16-bit analogue input section, a 2-channel 12-bit analogue output and 16 channels each of 5 V/TTL digital input and output on one Universal PCI card. The board supports both the 3.3 V and 5 V PCI bus, so it can be fitted in either slot type.The analogue inputs are jumper selectable between 32 single-ended and 16 differential channels, with a programmable gain of 1, 2, 4 or 8. An 8192-sample hardware FIFO and a MagicScan controller for multi-channel scanning support high-speed acquisition. The onboard Card ID switch lets software identify each board when two or more cards are installed in the same computer.This board is fully compatible with the PCI-1602/F and can be used as a direct replacement without changes to software or driver. A DLL, an ActiveX control and sample programs for several languages are provided, and the card supports Linux, DOS and Windows. The order includes one CA-3710 D-Sub cable.ApplicationsHigh speed data acquisition systemsProcess monitoring and controlVibration analysisDigital pattern generation from digital I/O port
The PCI-1602FU CR is a high-speed multifunction card for PC-based data acquisition. This ordering code is the 200 kS/s version of the PCI-1602U series, sampling its 16-bit analog inputs at up to 200 kS/s and buffering results in an 8192-sample hardware FIFO, which helps when capturing fast or multi-channel signals on a host PC.The board fits Universal PCI slots and works with both 3.3 V and 5 V PCI buses. Analog inputs can be set to 32 single-ended or 16 differential channels by jumper, with programmable gain of 1, 2, 4 and 8. Alongside the analogue side, it offers a 2-channel 12-bit analog output and 16 channels each of 5 V/TTL digital input and output, with pull-high and pull-low resistors on the DI channels. The board is pin-compatible with the PCI-1602/F and does not need changes to existing software or drivers.This order includes one CA-4002 D-Sub connector. Driver support covers Linux, DOS and Windows, with a DLL and ActiveX control plus sample programs for several C, Visual Basic, C#.NET and LabVIEW environments. A Card ID switch lets software identify each card when two or more are installed in the same computer.ApplicationsHigh speed data acquisition systemProcess monitor and controlVibration analysisDigital pattern generator from digital I/O port
The PCI-1602FU/S CR is a high-speed PC-based multifunction board for engineers who need fast, multichannel analogue acquisition alongside digital I/O. Its 16-bit converter samples at up to 200 kS/s, and the 8192-sample FIFO buffers data so the host PC can keep pace with acquisition.Analogue inputs are available as 32 single-ended or 16 differential channels, with programmable gain of 1, 2, 4 and 8 and bipolar ranges from ±1.25 V to ±10 V. A built-in MagicScan controller handles multi-channel scanning, and triggering can be software, internal pacer, or external (5 V/TTL). Two 12-bit analogue outputs and 16 digital inputs and 16 digital outputs (5 V/TTL) complete the I/O set.The board fits a 3.3 V/5 V Universal PCI slot and includes a Card ID switch, so individual cards can be identified in software when two or more are installed in the same computer. It is a drop-in replacement for the PCI-1602/F with no software or driver changes, and the supplied CA-3710 D-Sub cable connects it to external signals.ApplicationsHigh-speed data acquisition systemsProcess monitoring and controlVibration analysisDigital pattern generation from the digital I/O port
PCI-1002HU CR is the high-gain, 44 kS/s variant of the PCI-1002 series, a universal PCI multifunction board for acquiring analogue signals alongside digital I/O on a PC. Its 3.3 V/5 V universal PCI interface suits a wide range of host systems, and it supports Card ID via an SMD switch for identifying cards in multi-board setups.The analogue front end offers 32 single-ended or 16 differential channels at 12-bit resolution, with gains of 1, 10, 100 and 1000 and bipolar ranges from ±10 V down to ±0.01 V. Sixteen 5 V/TTL digital inputs with pull-high and pull-low resistors let an unconnected or interrupted input be given a defined state, and sixteen 5 V/TTL digital outputs are available for control tasks. The board includes one CA-4002 D-Sub connector.Software support covers Linux, DOS and Windows, with a DLL, an ActiveX control and sample programs for a range of development languages, including C#.NET, Visual Basic.NET and LabVIEW, to help users build their own applications.ApplicationsLaboratory automationProduction testSensor interface