PDS-732 Programmable Serial-to-Ethernet Device Server, 2x RS-232/1x RS-485
PDS-732 CR links two RS-232 ports and one RS-485 port to Ethernet, with 4 digital inputs, 4 digital outputs and Modbus TCP to RTU/ASCII gateway function. Includes CA-0910 cable.
- Two RS-232 ports and one RS-485 port bridge serial devices onto a 10/100 Base-TX Ethernet network
- VxComm driver extends PC COM ports; supports 32/64-bit Windows 7 SP1/10/2012/2016
- Modbus TCP to RTU/ASCII gateway function for SCADA and HMI communication
- Programmable with the Xserver structure on the built-in MiniOS7
- 4 digital inputs with latched D/I and counter functions
- 4 open-collector NPN digital outputs rated 30 VDC, 100 mA max.
278,00 € per piece
| 1–9 pcs | 278,00 € | |
|---|---|---|
| 10–30 pcs | 269,00 € | −3 % |
| 31+ pcs | 264,00 € | −5 % |
Tuotetiedot "PDS-732 Programmable Serial-to-Ethernet Device Server, 2x RS-232/1x RS-485"
The PDS-732 CR is a programmable device server that connects RS-232 and RS-485 serial equipment to an Ethernet network. Its built-in COM ports can be presented as standard COM ports on a Windows PC through the VxComm driver and utility, so PC software that expects a local COM port can reach serial devices over the network.
The unit runs the built-in MiniOS7 operating system and can be programmed with the Xserver structure for custom Ethernet applications. It also works as a Modbus TCP to RTU/ASCII gateway, allowing Modbus TCP SCADA and HMI systems to communicate with serial Modbus devices.
Four digital inputs (dry contact, source type with common ground, ON from +3.5 to +30 V) and four open-collector NPN digital outputs (30 VDC, 100 mA max.) add discrete I/O alongside the serial ports. The plastic housing mounts on DIN-rail or wall, with an operating range of -25 ~ +75 °C. The CA-0910 cable is included.
Applications
- Factory Automation
- Building Automation
- Home Automation
| Product type: | Serial-to-Ethernet device server |
|---|---|
| Interface: | Ethernet, RS-232, RS-485 |
| Protocol: | Modbus TCP |
| Digital inputs: | 4 |
| Digital outputs: | 4 |
| Ports: | 2x RS-232, 1x RS-485 |
| Power input: | +10 ~ 30 VDC |
| Operating temperature: | -25 ~ +75 °C |
| Mounting: | DIN-rail, Wall |
| Housing: | Plastic |
Specifications
| CPU Module | |
|---|---|
| CPU | 80186-80 MHz or compatible |
| EEPROM | 16 KB; Data retention: 40 years; 1,000,000 erase/write cycles. |
| Flash | 512 KB ; Erase unit is one sector (64 KB) ; 100,000 erase/write cycles |
| SRAM | 512 KB |
| Watchdog Timer | Yes |
| LED Indicators | |
| Status | 1 x Power |
| Digital Input | |
| Channels | 4 |
| Type | Dry Contact |
| Sink/Source (NPN/PNP) | Source, Common Ground |
| ON Voltage Level | +3.5 ~ +30 V |
| OFF Voltage Level | +1 V max. |
| Digital Output | |
| Channels | 4 |
| Type | Open Collector |
| Sink/Source (NPN/PNP) | Sink (NPN) |
| Load Voltage | 30 VDC, max. |
| Load Current | 100 mA, max. |
| Ethernet | |
| Ports | 10/100 Base-TX, RJ-45 port (Auto-negotiating, auto MDI/MDI-X, LED indicator) |
| COM Ports | |
| Ports | 2 x 5-wire RS-232 1 x RS-485 |
| Baud Rate | 115200 bps Max. |
| Bias Resistor | Yes, 1 KΩ |
| Parity | None, Even, Odd, Mark, Space None parity is required when using 8 data bits and 2 stop bits on COM1/COM2. |
| Data Bit | 7, 8: for COM1 and COM2 5, 6, 7, 8: for COM3 |
| Stop Bit | 1, 2: for COM1 ~ COM3 |
| Node Address | 254 (max.) |
| Power | |
| Consumption | 2.0 W |
| Powered from Terminal Block | +10 ~ 30 VDC |
| Mechanical | |
| Casing | Plastic |
| Dimensions (mm) | 72 mm x 35 mm x 123 mm (W x L x H) |
| Installation | DIN-Rail or Wall mounting |
| Environment | |
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -40 ~ +80 °C |
| Humidity | 5 ~ 90% RH, non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Kirjaudu sisään