CAN-Logger200 2-Port CAN Bus Data Logger with SD/SDHC Storage
Two-port CAN bus data logger that time-stamps and stores CAN messages to SD/SDHC flash, with USB 2.0 configuration, M12 CAN connectors and photocoupler isolation on the CAN side.
- Two CAN ports compliant with CAN 2.0A and CAN 2.0B and ISO 11898-2
- Time-stamped logging at 10 us, with up to 15000 fps receive rate per channel
- Continuous logging to SD/SDHC flash, 4 GB default and up to 32 GB supported
- Filter support for CAN bus acceptance filtering
- USB 2.0 High Speed port for configuration and CAN message transmit/receive via utility
- 2500 Vrms photocoupler isolation and 3 kV galvanic isolation on the CAN port
537,00 € per piece
| 1–9 pcs | 537,00 € | |
|---|---|---|
| 10–30 pcs | 521,00 € | −3 % |
| 31+ pcs | 510,00 € | −5 % |
Tuotetiedot "CAN-Logger200 2-Port CAN Bus Data Logger with SD/SDHC Storage"
CAN-Logger200 CR is a two-port CAN bus data logger for capturing traffic on CAN networks without a PC attached for the whole session. Each CAN message is time-stamped at 10 us resolution and written to an SD or SDHC card, so recorded data can be reviewed later for analysis and fault diagnosis.
Logging runs continuously and stores binary files on a card, 4 GB by default and up to 32 GB supported. When the card is full, the logger overwrites older data. A bundled configuration utility sets the CAN acceptance filters and baud rate from 10 kbps to 1 Mbps, and can also transmit and receive CAN messages over the USB 2.0 Type B port.
The CAN side is isolated, with 2500 Vrms photocoupler isolation and 3000 VDC DC-to-DC isolation on the CAN port. Each M12 5-pin CAN connector has a DIP-switch selectable 120 Ω terminal resistor. The unit runs from +10 VDC to +30 VDC or from USB power, and its metal housing is designed for wall mounting.
Applications
- CAN bus network data collection and analysis
- CAN bus diagnostics and troubleshooting
- Recording CAN traffic for later review
- Monitoring and control of CAN-based industrial systems
| Product type: | CAN bus data logger |
|---|---|
| Interface: | CAN, USB 2.0 |
| Protocol: | CAN 2.0A/2.0B |
| Ports: | 2 |
| Isolation: | 2500 Vrms (photocoupler), 3000 VDC (DC-to-DC) |
| Power input: | +10 VDC ~ +30 VDC or USB |
| Operating temperature: | -25 ~ +75 °C |
| Mounting: | Wall mount |
| Housing: | Metal |
Specifications
| Data Logger | |
|---|---|
| Trigger | Log continuously |
| Time Stamp | 10 us |
| Storage Media | SD card, default: 4GB, max. support: 32 GB |
| File Format | Binary |
| Configuration | Utility tool |
| Mode | Overwrite when storage space is full |
| LED Indicators | |
| Status | 1 x Power 1 x Module status 1 x SD status 3 x CAN status |
| USB | |
| Specification | USB 2.0 High Speed |
| Transfer Speed | 480 Mbit/s, High Speed mode |
| Connector | 1 x USB (Type B) (Utility port) |
| Driver | Built-in Windows 7/8.1/10 |
| CAN | |
| Ports | 2 |
| Specification | ISO-11898-2, CAN 2.0A and CAN 2.0B |
| Baud Rate | 10 k ~ 1 M bps |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for photocoupler |
| Terminal Resistor | DIP switch for the 120 Ω terminal resistor |
| Filter | Yes |
| Pin Assignment | 2 x 5-Pin male M12 |
| Data Flow | 15000 fps for Rx |
| Power | |
| Input Range | +10 VDC ~ +30 VDC or USB power delivery |
| Consumption | 2.5 W |
| Mechanical | |
| Casing | Metal |
| Dimensions (mm) | 102 x 102 x 44 (W x L x H) |
| Installation | Wall Mount |
| Environment | |
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -30 ~ +80 °C |
| Humidity | 10 ~ 90% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Kirjaudu sisään