XV484 4/8-ch Counter/Frequency/Encoder Expansion Board, 32-bit
32-bit counter, frequency and encoder input expansion board with 8 channels, individual channel configuration and a Modbus RTU RS-232 port.
- Eight up-counter or frequency channels, or four encoder input channels
- 32-bit counter (4,294,967,295 maximum count)
- Individual channel configuration, with different modes on each channel
- Programmable digital filter to suppress short noise pulses
- Virtual battery backup preserves counter values; preset values supported
- Maximum speed of 1 MHz with 2000 VDC intra-module isolation
133,00 € per piece
| 1–9 pcs | 133,00 € | |
|---|---|---|
| 10–30 pcs | 129,00 € | −3 % |
| 31+ pcs | 126,00 € | −5 % |
Información sobre el producto "XV484 4/8-ch Counter/Frequency/Encoder Expansion Board, 32-bit"
XV484 CR is a 32-bit, high-speed counter, frequency and encoder input expansion board from the XV-board range. It accepts up to eight up-counter or frequency channels, or four encoder channels, so one board can cover a mixed set of pulse-counting and speed-measurement tasks.
Each channel can be configured independently. Some channels can run as up counters while others measure frequency or act as up/down or encoder inputs in the same board. A programmable digital filter rejects noise by ignoring pulses whose high or low width is shorter than the filter's minimum width. Counter values can be preserved through a virtual battery backup, and preset values can be loaded for each counter input.
- Up/down (CW/CCW), direction/pulse and A/B phase quadrant counting for encoder feedback
- Frequency inputs rated up to 1 MHz, with accuracy specified per frequency band
- Isolated from the module with 2000 VDC intra-module isolation
- Modbus/RTU over RS-232 at 115200 bps, N, 8, 1
Applications
- Pulse and event counting
- Frequency and speed measurement
- Rotary encoder position feedback
- Industrial PAC expansion with counter inputs
| Product type: | Expansion Board |
|---|---|
| Interface: | RS-232 |
| Protocol: | Modbus RTU |
| Digital inputs: | 8 |
| Ports: | 1 |
| Isolation: | 2000 VDC |
| Power input: | 5 VDC |
| Operating temperature: | -25 ~ +75 °C |
Specifications
| Isolation | |
|---|---|
| Intra-module Isolation | 2000 VDC |
| EMS Protection | |
| ESD (IEC 61000-4-2) | ±4 kV Contact For Each Terminal ±8 kV Air For Random Terminal |
| Counter/Frequency/Encoder Input | |
| Channels | 4-channel Up/Down Counter (CW/CCW) 4-channel Dir/Pulse Counter (Bi-direction) 4-channel A/B Phase (Quadrant Counting) 8-channel Up Counter 8-channel Frequency |
| Type | Counter, Frequency or Encoder, Wet Contact |
| Counter Mode | Up or Up/Down |
| Encoder Mode | CW/CCW, Dir/Pulse, AB Phase |
| Frequency Mode | Yes |
| Counter/Encoder Bits | 32-bit (4,294,967,295) |
| Sink/Source (NPN/PNP) | Sink |
| ON Voltage Level | +5 VDC ~ +24 VDC |
| OFF Voltage Level | +3 VDC Max |
| Frequency Accuracy | 1 Hz ~ 200 kHz = ±0.025% of Input Frequency (Note1) 200 kHz ~ 1 MHz = ±0.1% of Input Frequency |
| Individual Channel Configuration | Yes |
| Max. Speed | 1 MHz |
| COM Ports | |
| Ports | 1 x RS-232 |
| Baud Rate | 115200 bps |
| Data Format | N, 8, 1 |
| Protocol | Modbus/RTU |
| Power | |
| Consumption | 1.2 W |
| Powered from Terminal Block | 5 VDC |
| Mechanical | |
| Dimensions (mm) | 59 mm x 82 mm x 13 mm (W x L x H) |
| Environment | |
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -30 ~ +80 °C |
| Humidity | 10 ~ 90% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Iniciar sesión