I-8120W-G 1-Port Programmable CAN Module, Parallel Bus Type for PAC Systems
Single-port programmable CAN module with an NXP SJA1000T controller and ISO 11898-2 transceiver, designed to run user firmware on WinPAC-8000, ViewPAC and XPAC-8000 controllers.
- Single CAN port with 5-pin screw terminal connector, compatible with CAN 2.0A and 2.0B
- NXP SJA1000T CAN controller with 16 MHz clock and ISO-11898-2 transceiver
- User-programmable firmware on an 80186 CPU running at 80 MHz, with 512 KB flash and 512 KB SRAM
- Default baud rate 10 kbps to 1 Mbps, with user-defined baud rates supported
- Switchable 120 Ω terminal resistor for CAN bus termination
- CAN message timestamps with ±1 ms precision and an inside real-time clock
293,00 € per piece
| 1–9 pcs | 293,00 € | |
|---|---|---|
| 10–30 pcs | 284,00 € | −3 % |
| 31+ pcs | 278,00 € | −5 % |
Informace o výrobku "I-8120W-G 1-Port Programmable CAN Module, Parallel Bus Type for PAC Systems"
The I-8120W-G adds a CAN 2.0A/2.0B interface to WinPAC-8000, ViewPAC and XPAC-8000 controllers over a parallel bus. Its on-board 80186 CPU runs user-defined firmware, so engineers can handle CAN traffic locally, with the main controller taking care of the higher-level logic. The -G variant is the RoHS-compliant version listed under ordering code I-8120W-G CR.
Designed for distributed real-time control, the module supports baud rates from 10 kbps to 1 Mbps by default and allows user-defined rates. A switchable 120 Ω terminal resistor simplifies bus termination, and CAN messages are timestamped with ±1 ms precision. Isolation is rated at 3000 VDC for the DC-to-DC section and 2500 Vrms for the photocoupler.
Because the module can be programmed, it can also act as a multi-CAN-port device server that bridges CAN with RS-232, RS-485 or Ethernet ports, letting integrators build applications that span different communication protocols. Firmware and demos are supplied with C/C++ libraries, plus VC6 and VS 2005 demos and libraries.
Applications
- Robust CAN communication in solar ships
- Multi-port CAN programmable device server
- Bridging CAN with RS-232, RS-485 and Ethernet networks
- Distributed real-time control over CAN bus
| Product type: | Programmable CAN module |
|---|---|
| Interface: | CAN |
| Protocol: | CAN 2.0A/2.0B |
| Ports: | 1 |
| Isolation: | 3000 VDC (DC-to-DC), 2500 Vrms (photocoupler) |
| Operating temperature: | -25 ~ +75 °C |
Specifications
| Software | |
|---|---|
| Driver | I-8120W (for designing user-defined firmware), WinPAC, ViewPAC, XPAC, XPAC-CE6 (The XPAC series PAC only support one I-8120W) |
| SDK | TC/BC/TC++/BC++, eVC++ 4.0, VC++ 2005, C#.net 2005, VB.net 2005 |
| CPU Module | |
| CPU | 80186, 80 MHz or compatible |
| EEPROM | 16 KB |
| Flash | 512 KB |
| SRAM | 512 KB |
| Watchdog Timer | Watchdog IC |
| LED Indicators | |
| Status | 1 x Power 1 x CAN status 1 x Operating mode |
| CAN | |
| Controller | NXP SJA1000T with 16 MHz clock |
| Specification | ISO-11898-2, CAN 2.0A and CAN 2.0B |
| Baud Rate | 10 k ~ 1 M bps |
| Isolation | 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple |
| Terminal Resistor | Switch for 120 Ω terminal resistor |
| Power | |
| Consumption | 1.5 W |
| Mechanical | |
| Dimensions (mm) | 31 x 91 x 115 (W x L x H) |
| Environment | |
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -30 ~ +80 °C |
| Humidity | 10 ~ 90% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Přihlásit