I-2533CS-FD CAN/CAN FD to Single-mode Fibre Bridge, 30 km, SC Connector
Local CAN/CAN FD to single-mode fibre bridge that links two CAN networks over up to 30 km through an SC connector, with a switchable 120 Ω terminator.
- Converts CAN and CAN FD signals to single-mode fibre for up to 30 km transmission
- Compliant with ISO 11898-2 and CAN specification 2.0 A/B and FD
- CAN FD data-field bit rates from 100 kbps to 10 Mbps; CAN bit rates from 10 kbps to 1 Mbps
- Different baud rates on each side, so the two CAN networks do not need to match
- Switchable 120 Ω terminator and DIP switch for CAN/CAN FD baud rate setting
- Fibre broken-line detection and CAN message filter configuration
288,00 € per piece
| 1–9 pcs | 288,00 € | |
|---|---|---|
| 10–30 pcs | 279,00 € | −3 % |
| 31+ pcs | 274,00 € | −5 % |
Informace o výrobku "I-2533CS-FD CAN/CAN FD to Single-mode Fibre Bridge, 30 km, SC Connector"
The I-2533CS-FD bridges two CAN or CAN FD networks over single-mode fibre. It converts the electrical CAN/CAN FD signal to optical transmission, so the physical length of a CAN segment is no longer limited by copper cabling. It is a practical choice where a CAN bus must span a site, a building or a distance beyond the reach of standard bus wiring.
Each network runs at its own bit rate, so the two sides can operate with different CAN or CAN FD baud rates. A bus error on one network does not disrupt the other, which helps keep faults contained. Basic CAN message routing is available through Group ID settings, and message filtering can be configured on the CAN side.
The unit mounts on a DIN-rail and is powered from +10 VDC to +30 VDC. Status LEDs show power, CAN activity and fibre status, and fibre broken-line detection is included. Firmware can be updated over USB.
Applications
- Linking two CAN or CAN FD bus networks over long single-mode fibre runs
- Extending CAN bus segments beyond the distance limits of electrical cabling
- Isolating bus faults between separate CAN networks
- Connecting CAN networks that operate at different bit rates
| Product type: | CAN/CAN FD fibre bridge |
|---|---|
| Interface: | CAN/CAN FD, single-mode fibre (SC) |
| Protocol: | CAN 2.0 A/B, CAN FD |
| Ports: | 1 |
| Power input: | +10 ~ +30 VDC |
| Operating temperature: | -25 ~ +75 °C |
| Mounting: | DIN-rail |
| Housing: | Plastic |
Specifications
| LED Indicators | |
|---|---|
| Status | 1 x Power, 3 x CAN status, 2 x Fiber status |
| Fiber | |
| Fiber Cable | 8.3/125, 8.7/125, 9/125 or 10/125 μm |
| Wavelength | 1310 nm |
| TX Output | -15 dBm Min. , -8 dBm Max. |
| Transmission Distance | 30 km (9/125 μm recommended) |
| RX Sensitivity | -34 dBm Max. |
| RX Overload | -5 dBm Max. |
| Budget | 19 dBm |
| Propagation Delay | 190 us (*Note1) |
| USB | |
| Specification | USB 2.0 High Speed (480Mbps) |
| Connector | USB Type B, Mini-B |
| Driver | Built-in Windows 7/8.1/10 |
| CAN | |
| Ports | 1 |
| Specification | ISO 11898-2, CAN 2.0 A/B and FD |
| Baud Rate | CAN bit rates: 10 k ~ 1 M bps, CAN FD bit rates for data field: 100 k ~ 10M bps (*Note2) |
| Terminal Resistor | Switch for 120Ω terminal resistor |
| Filter | Yes |
| Power | |
| Input Range | +10 VDC ~ +30 VDC |
| Consumption | 3 W |
| Mechanical | |
| Casing | Plastic |
| Dimensions (mm) | 33 x 127 x 101 (W x L x H) |
| Installation | DIN-Rail |
| Environment | |
| Operating Temperature | -25 ~ +75 °C |
| Storage Temperature | -30 ~ +80 °C |
| Humidity | 10 ~ 90% RH, Non-condensing |
Specifications as published by the manufacturer. Subject to change.
Downloads
Přihlásit